Abstract：Using carbon non-woven fabric/fibre web as the reinforcements, porous C/C composites were prepared by chemical vapor infiltration (CVI) deposition of pyrolytic carbon, and then SiC was deposited by CVI and Cu was infiltrated under pressure successively. Fianlly, C/C-SiC-Cu composites were obained. The effects of density of porous C/C composites and SiC contents (volume fraction φ, the same below) on the flexural property of C/C-SiC-Cu composites were investigated, respectively. The results show that with the increase of porous C/C composites density and SiC content, pyrolytic carbon and SiC form an interface with high binding strength around carbon fibers, and the strengthening effect of them can be fully played. So the flexural strength of C/C-SiC-Cu composites significantly increase. When the bending process is carried out, pyrolytic carbon and SiC matrix can inhibit the pullout of carbon fibers. The flexural load-displacement curve of C/C-SiC-Cu composites is ups and downs step-like, showing obvious characteristics of pseudoplastic fracture.
[1] TANG S, HU C.Design, preparation and properties of carbon fiber reinforced ultra-high temperature ceramic composites for aerospace applications: areview[J]. Journal of Materials Science & Technology, 2017(2): 117-130. [2] 杨凡, 谢奥林, 张贝, 等. C/C复合材料密度及预氧化处理对SiC涂层的影响[J]. 粉末冶金材料科学与工程, 2021, 26(2): 132-138. YANG Fan, XIE Aolin, ZHANG Bei, et al.Effect of the density of C/C composites and pre-oxidation process on SiC coatings[J]. Materials Science and Engineering of Powder Metallurgy, 2021, 26(2): 132-138. [3] YU C H, HUANG C W, Chen C S, et al.A micromechanics study of competing mechanisms for creep fracture of zirconium diboride polycrystals[J]. Journal of the European Ceramic Society, 2013, 33(10): 1625-1637. [4] LEVINE S R, OPILA E J, HALBIG M C, et al.Evaluation of ultra-high temperature ceramics foraeropropulsion use[J]. Journal of the European Ceramic Society, 2001, 22(14/15): 2757-2767. [5] NAIR B G, ZHAO Q, COOPER R F.Geopolymer matrices with improved hydrothermal corrosion resistance for high- temperature applications[J]. Journal of Materials Science, 2007, 42(9): 3083-3091. [6] LI S, CHEN X, CHEN Z.The effect of high-temperature heat-treatment on the strength of C/C-SiC joints[J]. Carbon, 2010, 48(11): 3042-3049. [7] LI G, YAN Q, JIANREN X, et al.The stability of the coefficient of friction and wear behavior of C/C-SiC[J]. Tribology Letters, 2015, 58(1): 13-19. [8] 杜善义. 先进复合材料与航空航天[J]. 复合材料学报, 2007, 24(1): 1-12. DU Shanyi.Advanced composite materials and aerospace engineering[J]. Acta Materiae Compositae Sinica, 2007, 24(1): 1-12. [9] KRISHNARAO R V, ALAM M Z, DAS D K.In-situ formation of SiC, ZrB2-SiC and ZrB2-SiC-B4C-YAG coatings for high temperature oxidation protection of C/C composites-science direct[J]. Corrosion Science, 2018, 141: 72-80. [10] ABU E H, KRENKEL W, HUGEL S.Development of C/C-SiC brake pads for high-performance elevators[J]. International Journal of Applied Ceramic Technology, 2005, 2(2): 105-113. [11] ZHOU X, ZHU D, XIE Q, et al.Friction and wear properties of C/C-SiC braking composites[J]. Ceramics International, 2012, 38(3): 2467-2473. [12] SCITI D, SILVESTRONI L, ESPOSITO L, et al.Advances in transient-liquid-phase bonding of ultra-high temperature ZrC ceramics[J]. High Temperature Materials & Processes, 2012, 31(4/5): 501-511. [13] 赵向坤, 王雅雷, 熊翔, 等. 叠层缝合结构C/C-SiC复合材料微观结构与弯曲性能[J]. 中国有色金属学报, 2021, 31(7): 1869-1878. ZHAO Xiangkun, WANG Yalei, XIONG Xiang, et al.Microstructure and flexural properties of laminated suture structure C/C-SiC composites[J]. Transaction of Nonferrous Metals of China, 2021, 31(7): 1869-1878. [14] LI J P, MENG S H, WANG Z B, et al. Study on ZrC- 20vol.% SiC ultrahigh temperature ceramics by hot pressing[J]. Advanced Materials Research, 2012, 557/559: 772-775. [15] CHENG L, XU Y, ZHANG L, et al.Effect of carbon interlayer on oxidation behavior of C/SiC composites with a coating from room temperature to 1 500 ℃[J]. Materials Science and Engineering A, 2001, 300(1/2): 219-225. [16] MEI H, ZHANG D, XIA J, et al.The effect of hole defects on the oxidation behavior of two-dimensional C/SiC composites[J]. Ceramics International, 2016, 42(14): 15479-15484. [17] YANG X, WEI L, SONG W, et al.Effects of the single layer CVD SiC interphases on the mechanical properties of the C/SiC composites fabricated by PIP process[J]. Materials Science & Engineering A, 2012, 558(DEC15): 451-455. [18] YANG X, HU H F, ZHANG Y D, et al.Thermal shock properties of 3D-C/SiC composites prepared via polymer infiltration pyrolysis (PIP)[J]. Ceramics International, 2014, 40(7): 9087-9094. [19] ZHAO D, GUO T, FAN X, et al.Effect of pyrolytic carbon interphase on mechanical properties of mini T800-C/SiC composites[J]. Journal of Advanced Ceramics, 2021, 10(2): 219-226. [20] ZHANG Y, XIAO Z, WANG J, et al.Effect of C/C porous preform on the microstructure and flexural strength of C/C-SiC composites[J]. Journal of the Chinese Ceramic Society, 2008, 36(8): 1069-1073. [21] 苏哲安, 杨鑫, 黄启忠, 等. 高温热震对具有SiC涂层的C/C复合材料压缩性能的影响[J]. 粉末冶金材料科学与工程, 2012, 17(1): 102-108. SU Zhean, YANG Xin, HUANG Qizhong, et al.Influence of high temperature cyclic thermal shock on compression properties of C/C composites with SiC coating[J]. Materials Science and Engineering of Powder Metallurgy, 2012, 17(1): 102-108.
2022, Vol. 27 
