Preparation of porous graphene/SiC-based composite by direct ink write 3D printing
TANG Run1, LIU Hongjun1,2, LI Yajun1, LI Yamin1,2
1. School of Materials Science and Engineering, Lanzhou University of Technology, Lanzhou 730050, China; 2. State Key Laboratory of Advanced Processing and Recycling of Nonferrous Metals, Lanzhou University of Technology, Lanzhou 730050, China
Abstract：Graphene/SiCp/PCS slurry was prepared using graphene and SiC powder (SiCp) as fillers and polycarbosilane (PCS) as ceramic precursor, and then the porous lightweight conductive graphene/SiC-based composite was prepared by direct ink write 3D printing and high temperature pyrolysis method. The influences of slurry composition and printing process on 3D printing formability were investigated, and the microstructure and properties of composite were characterized. The results show that the formability of the extruded filament is suitable for printing when the slurry viscosity is about 32.0 Pa·s by controlling the solid content, graphene content in graphene/SiCp composite powder, and dispersant content. When the printing speed is 360 mm/min and the layer height is 0.48 mm, the formability of the lattic grid structure for 3D printing is optimal. After heating the printed green body at 1 100 ℃ for 2 h, PCS is pyrolyzed into ceramics, the average compressive strength and conductivity of the composite are 11 MPa and 8 S/m, respectively. This study provides a new pathway for the preparation of porous graphene/SiC-based composite.
唐润, 刘洪军, 李亚军, 李亚敏. 多孔石墨烯/SiC基复合材料的直写3D打印制备[J]. 粉末冶金材料科学与工程, 2024, 29(6): 505-513.
TANG Run, LIU Hongjun, LI Yajun, LI Yamin. Preparation of porous graphene/SiC-based composite by direct ink write 3D printing. Materials Science and Engineering of Powder Metallurgy, 2024, 29(6): 505-513.
[1] MAN Y R, DING G Q, LUO X, et al.A review on porous ceramics with hierarchical pore structure by 3D printing-based combined route[J]. Journal of Asian Ceramic Societies, 2021, 9(4): 1377-1389. [2] DEL-MAZO-BARBARA L, GINEBRA M P. Rheological characterisation of ceramic inks for 3D direct ink writing: a review[J]. Journal of the European Ceramic Society, 2021, 41(16): 18-33. [3] 祝贤智, 成会朝, 周承商, 等. 挤出式3D打印工艺制备WC-10Co硬质合金的显微结构与力学性能[J]. 粉末冶金材料科学与工程, 2023, 28(2): 141-150. ZHU Xianzhi, CHENG Huichao, ZHOU Chengshang, et al.Microstructure and mechanical properties of WC-10Co cemented carbide prepared by extrusion 3D printing[J]. Materials Science and Engineering of Powder Metallurgy, 2023, 28(2): 141-150. [4] 王文禹, 刘洪军. 多孔陶瓷的直写成型工艺研究进展[J]. 精密成形工程, 2023, 15(4): 186-196. WANG Wenyu, LIU Hongjun.Research progress in direct ink writing process of porous ceramics[J]. Journal of Netshape Forming Engineering, 2023, 15(4): 186-196. [5] ROMÁN-MANSO B, CHEVILLOTTE T, OSENDI M I, et al. Thermal conductivity of silicon carbide composites with highly oriented graphene nanoplatelets[J]. Journal of the European Ceramic Society, 2016, 36(16): 3987-3993. [6] YOU X, YANG J S, HUANG K, et al.Multifunctional silicon carbide matrix composites optimized by three-dimensional graphene scaffolds[J]. Carbon, 2019, 155: 215-222. [7] ZHANG Q, YOU X, TIAN L, et al.Fabrication and efficient electromagnetic waves attenuation of three-dimensional porous reduced graphene oxide/boron nitride/silicon carbide hierarchical structures[J]. Journal of Materials Science & Technology, 2023, 155: 192-201. [8] RAZMJOO A, BAHARVANDI H R, EHSANI N, et al.The effect of graphene addition on the properties of SiC ceramics-a review[J]. Journal of the Australian Ceramic Society, 2022, 58(2): 437-460. [9] 孙川, 何鹏飞, 胡振峰, 等. 含有石墨烯阵列的SiC基陶瓷材料的制备与力学性能[J]. 无机材料学报, 2024, 39(3): 267-273. SUN Chuan, HE Pengfei, HU Zhenfeng, et al.SiC-based ceramic materials incorporating GNPs array: preparation and mechanical characterization[J]. Journal of Inorganic Materials, 2024, 39(3): 267-273. [10] YANG Y F, ZHU T B, LIAO N, et al.Preparation of graphene nanoplatelets reinforced SiC composites by oscillatory pressure sintering[J]. Ceramic International, 2022, 48(14): 20563-20570. [11] 潘振雪, 郭香, 张宗波, 等. 3D打印用硅基陶瓷前驱体研究进展[J]. 宇航材料工艺, 2022, 52(1): 11-21. PAN Zhenxue, GUO Xiang, ZHANG Zongbo, et al.Research progress on silicon-based ceramic precursors for 3D printing[J]. Aerospace Materials & Technology, 2022, 52(1): 11-21. [12] 赵连仲, 李周瑶, 熊慧文, 等. 活性填料对聚碳硅烷基悬浮液直写成形3D碳化硅的影响[J]. 粉末冶金材料科学与工程, 2021, 26(2): 166-173. ZHAO Lianzhong, LI Zhouyao, XIONG Huiwen, et al.Effect of active fillers on direct ink writing 3D SiC on polycarbosilane suspension[J]. Materials Science and Engineering of Powder Metallurgy, 2021, 26(2): 166-173. [13] CHEN Y, CHEN M W, XIE W J, et al.Influence of polycarbosilane composition on the properties of SiC/SiC composite fabricated by precursor infiltration and pyrolysis process[J]. International Journal of Applied Ceramic Technology, 2024, 21(5): 3237-3247. [14] CHEN H H, WANG X F, XUE F D, et al.3D printing of SiC ceramic: direct ink writing with a solution of preceramic polymers[J]. Journal of the European Ceramic Society, 2018, 38(16): 5294-5300. [15] CHAUDHARY R P, PARAMESWARAN C, IDREES M, et al.Additive manufacturing of polymer-derived ceramics: materials, technologies, properties and potential applications[J]. Progress in Materials Science, 2022, 128: 100969. [16] LU D, CHENG S, JIN L, et al.Effect of temperature on SiC whiskers growth of SiCw/SiC composites based on selective laser sintering and their mechanical properties[J]. Journal of Alloys and Compounds, 2023, 938: 168624. [17] XIONG H W, CHEN H H, CHEN Z K, et al.3D-SiC decorated with SiC whiskers: chemical vapor infiltration on the porous 3D-SiC lattices derived from polycarbosilane-based suspensions[J]. Ceramics International, 2020, 46(5): 6234-6242. [18] XIONG H W, ZHAO L Z, CHEN H H, et al.Building SiC-based composites from polycarbosilane-derived 3D-SiC scaffolds via polymer impregnation and pyrolysis (PIP)[J]. Journal of the European Ceramic Society, 2021, 41(2): 1121-1131. [19] 唐润. 直写3D打印石墨烯/SiCp/SiC复合材料的制备与性能研究[D]. 兰州: 兰州理工大学, 2024. TANG Run.Preparation and properties of graphene/SiCp/SiC Composite for direct-writing 3D printing[D]. Lanzhou: Lanzhou University of Technology, 2024.
2024, Vol. 29 
