Abstract:SiC ceramic matrix composites were prepared by 3D direct ink and phrolysis writing using nano Ti and NiO particles as active fillers, polycarbosilane (PCS) as SiC ceramic precursor, n-hexane as solvent to prepare slurries. The rheological properties of the slurries were investigated. The phase and morphology of the ceramic matrix composites were characterized. The effects of active fillers (nano Ti particles and nano NiO particles) on the phase and morphology of 3D-SiC ceramic matrix composites were studied. The results show that the viscosity of the slurry is proportional to the mass fraction of PCS, and it has shear thinning phenomenon. The slurry with 75% PCS has stable printing performance. The nano Ti powder can effectively reduce the mass loss rate and linear shrinkage rate during pyrolysis at 1 450 ℃, and the mass loss and linear shrinkage decrease from 18.29% and 24.38% to 14.05% and 12.13% respectively, the ceramics contains TiC and SiC phases. Compared with Ti powder, NiO can be used as a surface modification catalyst for SiC, and SiC whisker clusters can be grown in situ on the surface of SiC ceramics through the gas liquid solid (V-L-S) growth mechanism.
赵连仲, 李周瑶, 熊慧文, 周科朝, 张斗. 活性填料对聚碳硅烷基悬浮液直写成形3D碳化硅的影响[J]. 粉末冶金材料科学与工程, 2021, 26(2): 166-173.
ZHAO Lianzhong, LI Zhouyao, XIONG Huiwen, ZHOU Kechao, ZHANG Dou. Effect of active fillers on direct ink writing 3D SiC on polycarbosilane suspension. Materials Science and Engineering of Powder Metallurgy, 2021, 26(2): 166-173.
[1] ECKEL Z C, ZHOU C Y, MARTIN J H, et al.Additive manufacturing of polymer-derived ceramics[J]. Science, 2016, 351(6268): 58-62. [2] KONIG K, BOFFA V, BUCHBJERG B, et al.One-step deposition of ultrafiltration SiC membranes on macroporous SiC supports[J]. Journal of Membrane Science, 2014, 472(1): 232-240. [3] ELYASSI B, SAHIMI M, TSOTSIS T T.Silicon carbide membranes for gas separation applications[J]. Journal of Membrane Science, 2007, 288(1/2): 290-297. [4] HOU Y, CHENG L F, ZHANG Y I, et al.Electrospinning of Fe/SiC hybrid fibers for highly efficient microwave absorption[J]. Acs Applied Materials & Interfaces, 2017, 9(8): 7265-7271. [5] YAJIMA S, HAYASHI J.Development of a silicon carbide fibre with high tensile strength[J]. Nature, 1976, 261(1): 683-685. [6] LI Y L, FAN H, SU D, et al.Synthesis, structures, and properties of bulk Si(O)C ceramics from polycarbosilane[J]. Journal of the American Ceramic Society, 2009, 92(10): 2175-2181. [7] RAHMAN A, SINGH A, HARIMKAR S P, et al.Mechanical characterization of fine grained silicon carbide consolidated using polymer pyrolysis and spark plasma sintering[J]. Ceramics International, 2014, 40(8): 12081-12091. [8] KIM Y W, EOM J H, WANG C M, et al.Processing of porous silicon carbide ceramics from carbon-filled polysiloxane by extrusion and carbothermal reduction[J]. Journal of the American Ceramic Society, 2008, 91(4): 1361-1364. [9] MISHRA M K, KUMAR S, RANJAN A, et al.Processing, properties and microstructure of SiC foam derived from epoxy-modified polycarbosilane[J]. Ceramics International, 2018, 44(2): 1859-1867. [10] FUKUSHIMA M, COLOMBO P.Silicon carbide-based foams from direct blowing of polycarbosilane[J]. Journal of the European Ceramic Society, 2012, 32(2): 503-510. [11] ZHU S M, FAHRENHOLTZ W G, HILMAS G E.Enhanced densification and mechanical properties of ZrB2-SiC processed by a preceramic polymer coating route[J]. Scripta Materialia, 2008, 59(1): 123-126. [12] GUPTA R K, MISHRA R, MUKHOPADHYAY K, et al.A new technique for coating silicon carbide onto carbon nanotubes using a polycarbosilane precursor[J]. Silicon, 2009, 1(2): 125-129. [13] WELNA D T, BENDER J D, WEI X L, et al.Preparation of boron-carbide/carbon nanofibers from a poly (norbornenyldecaborane) single-source precursor via electrostatic spinning[J]. Advanced Materials, 2005, 17(7): 859-862. [14] LI D, XIA Y N.Electrospinning of nanofibers: Reinventing the wheel[J]. Advanced Materials, 2004, 16(14): 1151-1170. [15] LU X F, WANG C, WEI Y.One-dimensional composite nanomaterials: Synthesis by electrospinning and their applications[J]. Small, 2009, 5(21): 2349-2370. [16] PIERIN G, GROTTA C, COLOMBO P, et al.Direct ink writing of micrometric SiOC ceramic structures using a preceramic polymer[J]. Journal of the European Ceramic Society, 2016, 36(7): 1589-1594. [17] ZOCCA A, GOMES C M, STAUDE A, et al.SiC ceramics with ordered porosity by 3D-printing of a preceramic polymer[J]. Journal of Materials Research, 2013, 28(17): 2243-2252. [18] ZOCCA A, ELSAYED H, BERNARDO E, et al.3D-printed silicate porous bioceramics using a non-sacrificial preceramic polymer binder[J]. Biofabrication, 2015, 7(2): 225008. [19] GORJAN L, TONELLO R, SEBASTIAN T, et al.Fused deposition modeling of mullite structures from a preceramic polymer and gamma-alumina[J]. Journal of the European Ceramic Society, 2019, 39(7): 2463-2471. [20] BAUER J, CROOK C, IZARD A G, et al.Additive manufacturing of ductile, ultrastrong polymer-derived nanoceramics[J]. Matter, 2019, 1(6): 1547-1556. [21] CHEN H H, WANG X F, XUE F D, et al.3D printing of SiC ceramic: Direct ink writing with a solution of preceramic polymers[J]. Journal of the European Ceramic Society, 2018, 38(16): 5294-5300. [22] LI S, DUAN W, ZHAO T, et al.The fabrication of SiBCN ceramic components from preceramic polymers by digital light processing (DLP) 3D printing technology[J]. Journal of the European Ceramic Society, 2018, 38(14): 4597-4603. [23] LEWIS J A.Direct ink writing of 3D functional materials[J]. Advanced Functional Materials, 2006, 16(17): 2193-2204. [24] LEWIS J A, GRATSON G M.Direct writing in three dimensions[J]. Materials Today, 2004, 7(7/8): 32-39. [25] LEWIS J A, SMAY J E, STUECKER J, et al.Direct ink writing of three-dimensional ceramic structures[J]. Journal of the American Ceramic Society, 2006, 89(12): 3599-3609. [26] XIONG H W, CHEN H H, CHEN Z K, et al.3D-SiC decorated with SiC whiskers: Chemical vapor infiltration on the porous 3D-SiC lattices derived from polycarbosilane-based suspensions[J]. Ceramics International, 2020, 46(5): 6234-6242. [27] XIONG H W, CHEN H H, ZHAO L Z, et al.SiCw/SiCp reinforced 3D-SiC ceramics using direct ink writing of polycarbosilane-based solution: Microstructure, composition and mechanical properties[J]. Journal of the European Ceramic Society, 2019, 39(8): 2648-2657. [28] XIONG H W, ZHAO L Z, CHEN H H, et al.3D SiC containing uniformly dispersed, aligned SiC whiskers: Printability, microstructure and mechanical properties[J]. Journal of Alloys and Compounds, 2019, 809, 151824. [29] COLOMBO P, MERA G, RIEDEL R, et al.Polymer-derived ceramics: 40 years of research and innovation in advanced ceramics[J]. Journal of the American Ceramic Society, 2010, 93(7): 1805-1837. [30] XIE Z F, CHEN Z H, LI Y Q, et al.Applications of active filler in the preparation of preceramic polymer derived ceramics[J]. Journal of Inorganic Materials, 2000, 15(2): 200-208. [31] PROUST V, BECHELANY M C, GHISLENI R, et al.Polymer- derived Si-C-Ti systems: From titanium nanoparticle-filled polycarbosilanes to dense monolithic multi-phase components with high hardness[J]. Journal of the European Ceramic Society, 2016, 36(15): 3671-3679. [32] CHEN Y F, LIU X Z, DENG X W.Factors affecting the growth of SiC nano-whiskers[J]. Journal of Materials Science & Technology, 2010, 26(11): 1041-1046. [33] LUO Y M, ZHENG Z M, MEI X N, et al.Synthesis and phase evolution of Si-C-Ti powder derived from poly (methylsilaacetylene) and Ti[J]. Materials Letters, 2008, 62(26): 4232-4234.