2025年07月28日 星期一 首页   |   期刊介绍   |   编 委 会   |   投稿指南   |   出版法规   |   出版伦理   |   期刊订阅   |   联系我们   |   留言板   |   广告合作   |   ENGLISH
粉末冶金材料科学与工程  2019, Vol. 24 Issue (2): 188-194    
  工艺技术 本期目录 | 过刊浏览 | 高级检索 |
Cf/Cu/C复合材料的抗弯性能
张欢1, 尹健1, 熊翔1, 张红波1, 徐亚楠1, 杨鹏翱2
1. 中南大学 粉末冶金国家重点实验室,长沙 410083;
2. 浙江亚太机电股份有限公司,杭州市萧山区亚太路1399号,杭州 311200
Flexural property of Cf/Cu/C composites
ZHANG Huan1, YIN Jian1, XIONG Xiang1, ZHANG Hongbo1, XU Ya’nan1, YANG Peng’ao2
1. State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083, China;
2. Zhejiang Asia-pacific Mechanical & Electronic Co., Ltd, 1399 Asia Pacific Road, Xiaoshan District, Hangzhou 311200, China;
全文: PDF (592 KB)   HTML (0 KB) 
输出: BibTeX | EndNote (RIS)      
摘要 分别以无纬布/网胎/铜网(A型)和网胎/铜网型(B型)预制体为增强体,采用化学气相渗透和树脂浸渍-炭化法增密制备以热解炭/树脂炭为基体的3种炭纤维混杂铜网增强炭基体(Cf/Cu/C)复合材料,热解炭在热解炭/树脂炭基体中的体积分数分别为38%(M1)、29%(M2)、19%(M3)。选用Instron3369型材料试验机测试材料的抗弯强度。研究预制体类型和热解炭含量对复合材料力学性能的影响。结果表明,预制体类型和热解炭含量是影响复合材料抗弯强度的重要因素。在垂直和平行方向上,A型预制体及B型预制体试样的抗弯强度都随热解炭含量的降低而降低。且对同一试样,垂直方向的抗弯强度均优于平行方向上的抗弯强度,但差异较小;A型Cf/Cu/C复合材料较B型Cf/Cu/C复合材料有更高的抗弯强度。弯曲断裂时,炭纤维从热解炭和树脂炭层中拔出,断口呈台 阶状。
服务
把本文推荐给朋友
加入我的书架
加入引用管理器
E-mail Alert
RSS
作者相关文章
张欢
尹健
熊翔
张红波
徐亚楠
杨鹏翱
关键词 Cf/Cu/C复合材料Cf/Cu预制体炭纤维抗弯性能断裂机制    
Abstract:Using non-woven fabric/fibre web/copper mesh (A-type) and fibre web/copper mesh (B-type) as reinforcements, three kinds of Cf/Cu/C composites were prepared by chemical vapor infiltration and impregnation- carbonization with resin carbon method. The percentage of pyrolytic carbon were 38% (M1), 29% (M2), 19% (M3) in the matrix. Respectively the flexural property of the composite was measured on Instron- 3369 mechanical testing machine. The effects of type of preform and pyrolytic carbon content on mechanical property were investigated. The results show that with the decrease of pyrolytic carbon content, the flexural strength of A-type and B-type composites decreases gradually in vertical and parallel direction. For the same specimen, the flexural strength of Cf/Cu/C composites in the vertical direction is better than that of parallel direction, but the difference is small. Compared with B-type Cf/Cu/C composites, A-type Cf/Cu/C composites have better mechanical property. When the bending is carried out, carbon fibers from pyrolytic carbon and resin carbon layers are pulled out, and fracture morphology is step-like.
Key wordsCf/Cu/C composites    Cf/Cu preform    carbon fibre    flecture property    fracture mechanism
收稿日期: 2018-11-16      出版日期: 2019-07-12
ZTFLH:  TB331  
基金资助:湖南省自然科学基金资助项目(2017JJ2309)
作者简介: 尹健,副研究员,博士。电话:13974827640;E-mail: jianyin@csu.edu.cn
引用本文:   
张欢, 尹健, 熊翔, 张红波, 徐亚楠, 杨鹏翱. Cf/Cu/C复合材料的抗弯性能[J]. 粉末冶金材料科学与工程, 2019, 24(2): 188-194.
ZHANG Huan, YIN Jian, XIONG Xiang, ZHANG Hongbo, XU Ya’nan, YANG Peng’ao. Flexural property of Cf/Cu/C composites. Materials Science and Engineering of Powder Metallurgy, 2019, 24(2): 188-194.
链接本文:  
http://pmbjb.csu.edu.cn/CN/     或     http://pmbjb.csu.edu.cn/CN/Y2019/V24/I2/188
版权所有 © 《粉末冶金材料科学与工程》编辑部
地址:长沙市麓山南路中南大学粉末冶金研究院 邮编:410083 电话:0731-88877163 邮箱:pmbjb@csu.edu.cn
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn