2025年05月16日 星期五 首页   |   期刊介绍   |   编 委 会   |   投稿指南   |   出版法规   |   出版伦理   |   期刊订阅   |   联系我们   |   留言板   |   广告合作   |   ENGLISH
粉末冶金材料科学与工程  2020, Vol. 25 Issue (2): 171-178    
  工艺技术 本期目录 | 过刊浏览 | 高级检索 |
新型浆料注射法制备C/C复合材料的显微组织及力学性能
胡姣, 李国栋, 张洋, 韩前武, 姜毅
中南大学 粉末冶金研究院国家重点实验室,长沙 410083
Microstructure and mechanical properties of C/C composites prepared by a novel slurry injection technique
HU Jiao, LI Guodong, ZHANG Yang, HAN Qianwu, JIANG Yi
State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083, China
全文: PDF (116146 KB)   HTML (0 KB) 
输出: BibTeX | EndNote (RIS)      
摘要 采用浆料注射法将天然鳞片石墨粉添加到纤维预制体中,并结合化学气相渗透工艺(CVI)制备C/C复合材料。通过X射线无损检测、扫描电镜、偏光显微镜和材料力学性能测试,研究石墨浆料注射对C/C复合材料显微组织与力学性能的影响。结果表明:石墨浆料注射可将石墨引入到纤维预制体中,替代部分热解炭,并为热解炭提供新的形核位点和沉积表面,加速CVI致密化进程;且石墨的加入有利于粗糙层热解炭的形成,提高材料的可石墨化度。经80 h 等温CVI制得密度为1.68 g/cm3的C/C复合材料,抗弯强度为69.07 MPa,与传统等温CVI工艺相比,抗弯强度相近,平均增密速率提高近3倍;热解炭将纤维和石墨连成一个整体,材料表现出一定的假塑性断裂。
服务
把本文推荐给朋友
加入我的书架
加入引用管理器
E-mail Alert
RSS
作者相关文章
胡姣
李国栋
张洋
韩前武
姜毅
关键词 浆料注射法CVIC/C复合材料显微组织力学性能    
Abstract:C/C composites were fabricated by novel slurry injection and chemical vapor infiltration (CVI). In the slurry injection step, natural flake graphite was introduced to carbon fiber preform. Microstructure and mechanical properties of the as-fabricated C/C composites were analysed by X-ray nondestructive test, scanning electron microscope (SEM) polarizing microscope (PLM), and mechanical properties test. The results show that the flake graphite which replaces part of pyrolytic carbon can be introduced by slurry injection. This injected flake graphite can provide additional nucleation sites thereby greatly promoting densification rate of CVI process. The addition of natural flake graphite is beneficial to the formation of rough lamina (RL) pyrolytic carbon (PyC) and increases the degree of graphitization of the composites. After 80 h CVI, C/C composites with a density of 1.68 g/cm3 and a flexural strength of 69.07 MPa are obtained. Compared with the C/C composites fabricated by traditional CVI process, the flexural strength is close while the average densification rate is nearly tripled. Moreover, carbon fibers and flake graphite are well connected by PyC and the obtained C/C composites shows pseudo-plasticity fracture.
Key wordsslurry injection    CVI    C/C composites    microstructure    mechanical properties
收稿日期: 2019-12-03      出版日期: 2020-06-19
ZTFLH:  TB332  
基金资助:GFKJ创新特区项目(17-163-**-ZF***-15-01)
通讯作者: 李国栋,教授,博士。电话:13087317973;E-mail: lgd63@163.com   
引用本文:   
胡姣, 李国栋, 张洋, 韩前武, 姜毅. 新型浆料注射法制备C/C复合材料的显微组织及力学性能[J]. 粉末冶金材料科学与工程, 2020, 25(2): 171-178.
HU Jiao, LI Guodong, ZHANG Yang, HAN Qianwu, JIANG Yi. Microstructure and mechanical properties of C/C composites prepared by a novel slurry injection technique. Materials Science and Engineering of Powder Metallurgy, 2020, 25(2): 171-178.
链接本文:  
http://pmbjb.csu.edu.cn/CN/     或     http://pmbjb.csu.edu.cn/CN/Y2020/V25/I2/171
版权所有 © 《粉末冶金材料科学与工程》编辑部
地址:长沙市麓山南路中南大学粉末冶金研究院 邮编:410083 电话:0731-88877163 邮箱:pmbjb@csu.edu.cn
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn