2025年08月13日 星期三 首页   |   期刊介绍   |   编 委 会   |   投稿指南   |   出版法规   |   出版伦理   |   期刊订阅   |   联系我们   |   留言板   |   广告合作   |   ENGLISH
粉末冶金材料科学与工程  2019, Vol. 24 Issue (6): 508-514    
  工艺技术 本期目录 | 过刊浏览 | 高级检索 |
真空度及碳含量对M2高速钢组织和拉伸性能的影响
刘瑞卿1, 何浩2, 娄嘉3, 李益民1,2, 李松1, 刘晨2, 秦健春2
1.中南大学,粉末冶金国家重点实验室,长沙 410083;
2.广西科技大学,材料科学与工程研究中心,柳州 545006;
3.湘潭大学 材料科学与工程学院,湘潭 411105
Effects of vacuum degree and carbon content on microstructure and tensile properties of M2 high speed steel
LIU Ruiqing1, HE Hao2, LOU Jia3, LI Yimin1,2, LI Song1, LIU Chen2, QIN Jianchun2
1. State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083, China;
2. Materials Science and Engineering Research Center, Guangxi University of Science and technology, Liuzhou 545006, China;
3. School of Materials Science and Engineering, Xiangtan University, Xiangtan 411105, China
全文: PDF (1377 KB)   HTML (1 KB) 
输出: BibTeX | EndNote (RIS)      
摘要 采用真空烧结工艺制备M2高速钢,研究真空度与碳含量对高速钢组织和拉伸性能的影响。结果表明:低真空度下(10-1 Pa)M2高速钢的有效烧结温度为1 220~1 230 ℃,在该区间内烧结相对密度可达96%以上,烧结体显微组织由奥氏体基体及M6C、MC碳化物组成;超过该温度区间进行烧结会使合金析出有害的共晶碳化物,导致高速钢强度显著下降。当真空度提高到10-3 Pa时,M2高速钢的烧结温度降低,显微组织中的碳化物更细小、分布更均匀。M2高速钢的相对密度为98%,拉伸强度为989 MPa,伸长率为7.1%。随碳含量升高,M2高速钢的烧结区间无明显变化,但在较低温度下烧结更容易实现致密化。当碳的质量分数为1.0%时,样品的相对密度为97%,拉伸强度为954 MPa,伸长率为7%。
服务
把本文推荐给朋友
加入我的书架
加入引用管理器
E-mail Alert
RSS
作者相关文章
刘瑞卿
何浩
娄嘉
李益民
李松
刘晨
秦健春
关键词 粉末冶金高速钢真空度碳含量力学性能    
Abstract:The M2 high speed steel was prepared by vacuum sintering process. The effects of vacuum and carbon content on microstructure and properties of M2 high speed steel were studied. The results show that the effective sintering temperature of M2 HSS under low vacuum (10-1 Pa) is 1 220-1 230 ℃, and its relative density is above 96%. The microstructure of M2 is composed of austenitic matrix, M6C and MC carbides after sintering. When vacuum degree increases to 10-3 Pa,the effective sintering temperature of M2 HSS decreases, and the carbides in the matrix are finer and more evenly distributed. The relative density of the sintered sample is 98%, and its tensile properties and elongation reached 989 MPa and 7.1%, respectively. With the increase of carbon content, there is no obvious change in sintering interval of M2 high-speed steel, but the densification can be easier to achieve at lower temperature. When the mass fraction of carbon is 1.0%, the relative density of the sample is 97%, its tensile strength and elongation are 954 MPa and 7%, respectively.
Key wordspowder metallurgy    high speed steel    vacuum degree    carbon content    mechanical properties
收稿日期: 2019-08-01      出版日期: 2020-06-19
ZTFLH:  TF124  
基金资助:湖南省科技计划(2017GK2264); 2019年广西高校中青年教师科研基础能力提升项目(2019KY0381); 柳州市科技计划(2018DH10505)
通讯作者: 李松,副教授,博士。电话:0731-88830911;E-mail: ls2011sl@csu.edu.cn   
引用本文:   
刘瑞卿, 何浩, 娄嘉, 李益民, 李松, 刘晨, 秦健春. 真空度及碳含量对M2高速钢组织和拉伸性能的影响[J]. 粉末冶金材料科学与工程, 2019, 24(6): 508-514.
LIU Ruiqing, HE Hao, LOU Jia, LI Yimin, LI Song, LIU Chen, QIN Jianchun. Effects of vacuum degree and carbon content on microstructure and tensile properties of M2 high speed steel. Materials Science and Engineering of Powder Metallurgy, 2019, 24(6): 508-514.
链接本文:  
http://pmbjb.csu.edu.cn/CN/     或     http://pmbjb.csu.edu.cn/CN/Y2019/V24/I6/508
版权所有 © 《粉末冶金材料科学与工程》编辑部
地址:长沙市麓山南路中南大学粉末冶金研究院 邮编:410083 电话:0731-88877163 邮箱:pmbjb@csu.edu.cn
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn