Abstract:Powder metallurgy process has significant advantages in production cost, freedom of composition design and so on, and is an effective way to manufacture low-cost and high-performance titanium alloys. In this paper, Ti-2Mn-2Sn-0.1B alloys were prepared by powder metallurgy, and the effects of annealing temperature on microstructure and mechanical properties of the alloy were studied. The results show that all of the Ti-2Mn-2Sn-0.1B alloys are composed of α, β, and TiB phases. Compared with the unannealed alloy, the β phase content in the alloy annealed at 750 ℃ increases, the flake and needle α′ phases are deposited in the alloy annealed at 850 ℃, and the α and β phases are distributed in layers in the alloy annealed at 950 ℃. All the alloys are mainly ductile fracture, and the alloy annealed at 950 ℃ has better mechanical properties, the layered α and β phase can provide good strengthening and hardening effects, and the microhardness (HV), ultimate tensile strength, and elongation are 335±16, (803±4) MPa, and (11.3±2.2)%, respectively.
方浩煜, 伍秋美, 袁铁锤. 退火温度对粉末冶金Ti-2Mn-2Sn-0.1B合金组织和力学性能的影响[J]. 粉末冶金材料科学与工程, 2024, 29(3): 246-254.
FANG Haoyu, WU Qiumei, YUAN Tiechui. Effects of annealing temperature on microstructure and mechanical properties of Ti-2Mn-2Sn-0.1B alloy by powder metallurgy. Materials Science and Engineering of Powder Metallurgy, 2024, 29(3): 246-254.
[1] AWAD A H, ALY H A, SAOOD M.Physical, mechanical, and corrosion properties of Ti-12Mo and Ti-15Mo alloys fabricated by elemental blend and mechanical alloying techniques[J]. Materials Chemistry and Physics, 2024, 312: 128661. [2] GWAK M, KIM S, LEE D J, et al.Post-annealing effect on the tensile deformation mechanism of a Ti-6Al-4V alloy manufactured via directed energy deposition[J]. Materials Science and Engineering A, 2022, 836: 142729. [3] SANTOS D M C, SIGNOR F, SCHNEIDER A D, et al. Powder metallurgical manufacturing of Ti-Nb alloys using coarse Nb powders[J]. Materials Research-Ibero-American Journal of Materials, 2024, 27: e20230478. [4] 段中元, 陈奏君, 祝贤智, 等. 约束氢致密化处理对粉末冶金Ti-6Al-4V合金致密度与力学性能的影响[J]. 粉末冶金材料科学与工程, 2022, 27(2): 171-179. DUAN Zhongyuan, CHEN Zoujun, ZHU Xianzhi, et al.Effects of confined hydrogen densification treatment on the density and mechanical properties of powder metallurgy Ti-6Al-4V alloy[J]. Materials Science and Engineering of Powder Metallurgy, 2022, 27(2): 171-179. [5] WANG Z, TAN Y, LI N.Powder metallurgy of titanium alloys: a brief review[J]. Journal of Alloys and Compounds, 2023, 965: 171030. [6] SOCHACKA P, MIKLASZEWSKI A, JURCZYK M.Development of β-type Ti-x at.% Mo alloys by mechanical alloying and powder metallurgy: phase evolution and mechanical properties (10≤x≤35)[J]. Journal of Alloys and Compounds, 2019, 776: 370-378. [7] 李佳辉, 胡汀, 蔡格梅. Ti-Cr-Mn三元系的相关系实验研究[J]. 粉末冶金材料科学与工程, 2021, 26(5): 419-427. LI Jiahui, HU Ting, CAI Gemei.Experimental investigation of phase relations in the Ti-Cr-Mn system[J]. Materials Science and Engineering of Powder Metallurgy, 2021, 26(5): 419-427. [8] CHANG S H, HUANG K T, CHEN Y F, et al.Effect of Mn content on mechanical properties and corrosion resistance of Ti-8Mo-xMn alloys through the vacuum sintering process[J]. Vacuum, 2024, 222: 112959. [9] ALSHAMMARI Y, YANG F, BOLZONI L.Mechanical properties and microstructure of Ti-Mn alloys produced via powder metallurgy for biomedical applications[J]. Journal of the Mechanical Behavior of Biomedical Materials, 2019, 91: 391-397. [10] LIU H W, BISHOP D P, PLUCKNETT K P.A comparison of Ti-Ni and Ti-Sn binary alloys processed using powder metallurgy[J]. Materials Science and Engineering A, 2015, 644: 392-404. [11] ZHOU X X, FANG H Y, YUAN T C, et al.Effect of slight Sn modification on mechanical properties and corrosion behavior of Ti-(2-4 wt%) Mn alloys fabricated via powder metallurgy[J]. Materials Characterization, 2023, 203: 113068. [12] TAO X W, XIA J Q, XU Y T, et al.Role of Cu content in microstructure, mechanical, corrosion, tribological and antibacterial behavior of spark plasma sintered Ti-B-xCu alloys for dental application[J]. Vacuum, 2024, 222: 113085. [13] YI X Y, WANG H Z, SUN K S, et al.Simultaneous enhancement of strength and ductility in quaternary Ti-V-Al-B light weight shape memory alloys with high transformation temperature[J]. Intermetallics, 2020, 126: 106943. [14] BOLZONI L, YANG F, ALSHAMMARI Y.Joint effect of β-eutectoid content and heat treatment on the properties of binary Ti-Cu and Ti-Mn alloys[J]. Journal of Alloys and Compounds, 2024, 992: 174510. [15] ALSHAMMARI Y, ALQATTAN F, YANG F, et al.Vacuum sintering and solution plus aging heat treatment of β eutectoid bearing binary Ti alloy[J]. International Journal of Refractory Metals and Hard Materials, 2020, 91: 105267. [16] CHEN B, WU Z, YAN T, et al.Experimental study on mechanical properties of laser powder bed fused Ti-6Al-4V alloy under post-heat treatment[J]. Engineering Fracture Mechanics, 2022, 261: 108264. [17] LI X, YE S, YUAN X, et al.Fabrication of biomedical Ti-24Nb-4Zr-8Sn alloy with high strength and low elastic modulus by powder metallurgy[J]. Journal of Alloys and Compounds, 2019, 772: 968-977. [18] CACCIAMANI G, RIANI P, VALENZA F.Equilibrium between MB2 (M=Ti, Zr, Hf) UHTC and Ni: a thermodynamic database for the B-Hf-Ni-Ti-Zr system[J]. Calphad, 2011, 35(4): 601-619. [19] ZHANG S, LIN J, WANG C, et al.Improvement of microstructure and mechanical properties of Sapphire/Kovar alloy joints brazed with Ag-Cu-Ti composite filler by adding B powders[J]. Journal of Manufacturing Processes, 2023, 99: 243-253. [20] MENG F, ZHANG R, AN Q, et al.Effects of forging deformation on variant selection and morphology of α in TiB/near α-Ti composites[J]. Materials Characterization, 2024, 211: 113839. [21] LIU L, LI S, ZHANG X, et al.Synthesis mechanism of pelleted heterostructure Ti64-TiB composites via an interdiffusion and self-organization strategy based on powder metallurgy[J]. Composites Part B: Engineering, 2024, 276: 111366. [22] LI L, MA P, ZHANG L, et al.Fabrication of TiB whiskers reinforced Ti6242 matrix composites by direct laser deposition: powder preparation, microstructure and mechanical property[J]. Composites Part B: Engineering, 2024, 268: 111068. [23] ZHENG Z Y, CHAI L J, LI Z H, et al.Effects of β-cooling rates on microstructural characteristics and hardness of Ti-5Al-5Mo-5V-3Cr-1Fe metastable β Ti alloy[J]. Materials Chemistry and Physics, 2022, 276: 125318. [24] 胡赓祥, 蔡珣, 戎咏华. 材料科学基础(第三版)[M]. 上海: 上海交通大学出版社, 2010: 395-397. HU Gengxiang, CAI Xun, RONG Yonghua.Fundamentals of Materials Science (3rd Edition)[M]. Shanghai: Shanghai Jiaotong University Press, 2010: 395-397. [25] ESMAILY M, MORTAZAVI S N, TODEHFALAH P, et al.Microstructural characterization and formation of α′ martensite phase in Ti-6Al-4V alloy butt joints produced by friction stir and gas tungsten arc welding processes[J]. Materials & Design, 2013, 47: 143-150. [26] 张豪胤. Cr、Nd元素对粉末冶金钛合金组织与性能的影响研究[D]. 洛阳: 河南科技大学, 2015. ZHANG Haoyin.Effect of Cr and Nd elements on microstructure and properties of powder metallurgy titanium alloys[D]. Luoyang: Henan University of Science and Technology, 2015. [27] SHI Q M, YANG S F, SUN Y, et al.In-situ formation of Ti-Mo biomaterials by selective laser melting of Ti/Mo and Ti/Mo2C powder mixtures: a comparative study on microstructure, mechanical and wear performance, and thermal mechanisms[J]. Journal of Materials Science & Technology, 2022, 115: 81-96. [28] ZHU W, LEI J, TAN C, et al.A novel high-strength β-Ti alloy with hierarchical distribution of α-phase: the superior combination of strength and ductility[J]. Materials & Design, 2019, 168: 107640. [29] LIN Y C, TANG Y, ZHANG X Y, et al.Effects of solution temperature and cooling rate on microstructure and micro-hardness of a hot compressed Ti-6Al-4V alloy[J]. Vacuum, 2019, 159: 191-199. [30] MANOGAR B, YANG F, BOLZONI L.Correlation between microstructure and tensile properties of powder metallurgy Ti-6Nb-x(Fe or Mn) alloys[J]. Journal of Alloys and Compounds, 2022, 926: 166805. [31] AL-MAKHZUMI G, DAHM K L, YANG F, et al.Powder metallurgy metastable Ti alloys via lean Fe and Mn additions[J]. Materials Chemistry and Physics, 2023, 308: 128244.