Fabrication of cylindrical Si3N4 ceramics by spark plasma sintering based on the powder bed technology
CAI Peibin1, GU Qiankun1, GUO Weiming1, LUO Sichun2, LIN Huatai1
1. School of Electromechanical Engineering, Guangdong University of Technology, Guangzhou 510006, China; 2. School of Mechanical and Electronic Engineering, Pingxiang University, Pingxiang 337055, China
Abstract:SiC powders with average particle sizes of 150 μm and 50 μm were mixed with graphite powders with average particle sizes of 150 μm and 50 μm respectively to obtain coarse particle size powder bed (150 μm SiC+150 μm graphite) and fine particle size (50 μm SiC+50 μm graphite); the volume fractions of SiC and graphite in the powder bed were both 50%. Pre-sintered cylindrical Si3N4 green body was sintered by spark plasma sintering (SPS) based on powder bed technology. The effects of two different particle size bed powders, pre-sintering temperature (1 400 ℃and 1 500 ℃) and powder bed recovery on the deformation degree, density, phase composition and microstructure of cylindrical Si3N4 ceramics were investigated. The research results show that the circular section retention of cylindrical Si3N4 ceramic prepared by combining the coarse particle size powder bed, a pre-sintering temperature of 1 500 ℃ and a recycled once powder bed is the best, reaching 93%; the Vickers hardness and fracture toughness are (18.73±0.24) GPa and (3.64±0.23) MPa·m1/2, respectively. Due to the low sintering temperature (1 500 ℃), the main phase of the as-sintered ceramics is α-Si3N4; the grain morphology is equiaxed. This study shows that the shape limitation of the Si3N4 ceramics prepared by SPS can be overcame by introducing the powder bed. This technology is expected to realize the preparation of high-performance Si3N4 ceramics with complex shapes.
蔡培彬, 顾乾坤, 郭伟明, 罗嗣春, 林华泰. 基于粉末床技术放电等离子烧结Si3N4陶瓷圆柱体[J]. 粉末冶金材料科学与工程, 2023, 28(2): 113-119.
CAI Peibin, GU Qiankun, GUO Weiming, LUO Sichun, LIN Huatai. Fabrication of cylindrical Si3N4 ceramics by spark plasma sintering based on the powder bed technology. Materials Science and Engineering of Powder Metallurgy, 2023, 28(2): 113-119.
[1] THOMPSON D.Tough cookery[J]. Nature, 1997, 389(6652): 675-677. [2] FUMFSCHILLING S, FETT T, HOFFMANN M J, et al.Mechanisms of toughening in silicon nitrides: the roles of crack bridging and microstructure[J]. Acta Materialia, 2011, 59(10): 3978-3989. [3] XU W W, YIN Z B, YUAN J T, et al.Reliability prediction of a microwave sintered Si3N4-based composite ceramic tool[J]. Ceramics International, 2021, 47(12): 16737-16745. [4] 刘杰, 蒋强国. 含三元烧结助剂的氮化硅陶瓷刀具切削性能研究[J]. 陶瓷学报, 2018, 39(4): 487-491. LIU Jie, JIANG Qiangguo.Cutting performance of silicon nitride ceramic tool containing ternary sintering additives[J]. Journal of Ceramics. 2018, 39(4): 487-491. [5] BHUSHAN B, SIBLEY L B.Silicon nitride rolling bearings for extreme operating conditions[J]. American Society of Lubrication Engineers Transactions, 1982, 25(4): 417-428. [6] 丁泽良, 曾晓红, 吴吉平, 等. 氮化硅陶瓷水煤浆喷嘴的损坏机理[J]. 硅酸盐学报, 2008, 36(S1): 63-66. DING Zeliang, ZENG Xiaohong, WU Jiping, et al.Failure mechanism of Si3N4 ceramic nozzles in coal water slurry industrial boilers[J]. Journal of the Chinese Ceramic Society. 2008, 36(S1): 63-66. [7] 武振飞, 王跃超, 陆丽芳, 等. 无压烧结氮化硅陶瓷的物理性能研究[J]. 硅酸盐通报, 2022, 41(5): 1782-1787. WU Zhenfei, WANG Yuechao, LU Lifang, et al.Physical properties of silicon nitride ceramics by pressureless sintering[J]. Bulletin of the Chinese Ceramic Society. 2022, 41(5): 1782-1787. [8] 周宇章, 魏万鑫, 罗嗣春, 等. 添加TiO2对Si3N4陶瓷刀具切削性能的影响[J]. 机械工程材料, 2022, 46(5): 64-69, 76. ZHOU Yuzhang, WEI Wanxin, LUO Sichun, et al.Effect of TiO2 addition on cutting performance of Si3N4 ceramic cutting tool[J]. Materials for Mechanical Engineering. 2022, 46(5): 64-69, 76. [9] LUO S C, GUO W M, PLUCKNETT K, et al.Improved toughness of spark-plasma-sintered Si3N4 ceramics by adding HfB2[J]. Ceramics International, 2021, 47(6): 8717-8721. [10] LEE C H, LU H H, WANG C A, et al.Effect of heating rate on spark plasma sintering of a nanosized β-Si3N4-based powder[J]. Journal of the American Ceramic Society, 2011, 94(4): 1182-1190. [11] WALKER L S, MAROTTO V R, RAFIEE M A, et al.Toughening in graphene ceramic composites[J]. American Chemical Society Nano, 2011, 5(4): 3182-3190. [12] TATARKO P, LOJANOVA S, DUSZA J, et al.Influence of various rare-earth oxide additives on microstructure and mechanical properties of silicon nitride based nanocomposites[J]. Materials Science and Engineering A, 2010, 527(18/19): 4771-4778. [13] VOISIN T, MONCHOUX J P, DURAND L, et al.An innovative way to produce γ-TiAl blades: spark plasma sintering[J]. Advanced Engineering Materials, 2015, 17(10): 1408-1413. [14] MANIÈRE C, DURAND L, WEIBEL A, et al. Spark- plasma-sintering and finite element method: from the identification of the sintering parameters of a submicronic α-alumina powder to the development of complex shapes[J]. Acta Materialia, 2016, 102: 169-175. [15] MANIÈRE C, DURAND L, WEIBEL A, et al. A sacrificial material approach for spark plasma sintering of complex shapes[J]. Scripta Materialia, 2016, 124: 126-128. [16] MANIÈRE C, NIGITO E, DURAND L, et al. Spark plasma sintering and complex shapes: the deformed interfaces approach[J]. Powder Technology, 2017, 320: 340-345. [17] HOCQUET S, DUPONT V, CAMBIER F, et al.Densification of complex shape ceramics parts by SPS[J]. Journal of the European Ceramic Society, 2020, 40(7): 2586-2596. [18] 中国国家标准化管理委员会. 精细陶瓷室温硬度试验方法: GB/T 16534—2009[S]. 北京: 中国标准出版社, 2009. Standardization Administration of China. Fine ceramics test method for hardness of monolithic ceramics at room temperature: GB/T 16534—2009[S]. Beijing: Standared Press of China, 2009. [19] EVANS A G, CHARLES E A, Fracture toughness determinations by indentation[J]. Journal of the American Ceramic Society, 1976, 59(7/8): 3710-372. [20] YU J J, WEI W X, GUO W M, et al.Enhanced mechanical properties of Si3N4 ceramics with ZrB2-B binary additives prepared at low temperature[J]. Journal of the European Ceramic Society, 2019, 39(15): 5102-5105. [21] TATARKO P, LOJANOVA S, DUSZA J.et al.Influence of various rare-earth oxide additives on microstructure and mechanical properties of silicon nitride based nanocomposites[J]. Materials Science and Engineering A, 2010, 527(18/19): 4771-4778.