基于粉末床技术放电等离子烧结Si<sub>3</sub>N<sub>4</sub>陶瓷圆柱体

doi:10.19976/j.cnki.43-1448/TF.2022083

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (577 KB) HTML (0 KB)
输出: BibTeX | EndNote (RIS)

摘要将平均粒径分别为150 μm和50 μm的SiC粉体与平均粒径分别为150 μm和50 μm的石墨粉体混合,得到粗粉末床(150 μm SiC+150 μm石墨)与细粉末床(50 μm SiC+50 μm石墨),粉末床中SiC与石墨的体积分数均为50%。采用粉末床技术对圆柱形Si₃N₄陶瓷预烧体进行放电等离子烧结,研究粗、细粉末床、预烧温度(1 400 ℃和1 500 ℃)和粉末床回收对等离子烧结Si₃N₄陶瓷圆柱体的变形程度、致密度、物相组成和显微结构的影响。结果表明,采用粗粒径粉末床、1 500 ℃预烧温度和回收使用一次的粉末床制备的Si₃N₄陶瓷圆柱体,横截面形状保持度最高,达到93%,维氏硬度和断裂韧性分别为(18.73±0.24) GPa和(3.64±0.23) MPa∙m^1/2。Si₃N₄陶瓷的主相为α-Si₃N₄,晶粒形貌为等轴状。通过引入粉末床可克服放电等离子烧结制备Si₃N₄陶瓷制品的形状限制,有望实现高性能异形Si₃N₄陶瓷的制备。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	蔡培彬
	顾乾坤
	郭伟明
	罗嗣春
	林华泰

关键词 ：异形Si₃N₄陶瓷, 粉末床, 放电等离子烧结, 圆形截面保持度, 力学性能

Abstract：SiC powders with average particle sizes of 150 μm and 50 μm were mixed with graphite powders with average particle sizes of 150 μm and 50 μm respectively to obtain coarse particle size powder bed (150 μm SiC+150 μm graphite) and fine particle size (50 μm SiC+50 μm graphite); the volume fractions of SiC and graphite in the powder bed were both 50%. Pre-sintered cylindrical Si₃N₄ green body was sintered by spark plasma sintering (SPS) based on powder bed technology. The effects of two different particle size bed powders, pre-sintering temperature (1 400 ℃and 1 500 ℃) and powder bed recovery on the deformation degree, density, phase composition and microstructure of cylindrical Si₃N₄ ceramics were investigated. The research results show that the circular section retention of cylindrical Si₃N₄ ceramic prepared by combining the coarse particle size powder bed, a pre-sintering temperature of 1 500 ℃ and a recycled once powder bed is the best, reaching 93%; the Vickers hardness and fracture toughness are (18.73±0.24) GPa and (3.64±0.23) MPa·m^1/2, respectively. Due to the low sintering temperature (1 500 ℃), the main phase of the as-sintered ceramics is α-Si₃N₄; the grain morphology is equiaxed. This study shows that the shape limitation of the Si₃N₄ ceramics prepared by SPS can be overcame by introducing the powder bed. This technology is expected to realize the preparation of high-performance Si₃N₄ ceramics with complex shapes.

Key words： complex shape nitride silicon powder bed spark plasma sintering circular section retention mechanical property

收稿日期: 2022-10-30 出版日期: 2023-05-04

ZTFLH:

TB321

基金资助:国家自然科学基金资助项目(52172066)

通讯作者: 郭伟明,教授,博士。电话：020-39332212;E-mail: guo1238@126.com;罗嗣春,讲师,博士。电话：13667300329;E-mail: zcyxlsc@163.com

引用本文:

蔡培彬, 顾乾坤, 郭伟明, 罗嗣春, 林华泰. 基于粉末床技术放电等离子烧结Si₃N₄陶瓷圆柱体[J]. 粉末冶金材料科学与工程, 2023, 28(2): 113-119.
CAI Peibin, GU Qiankun, GUO Weiming, LUO Sichun, LIN Huatai. Fabrication of cylindrical Si₃N₄ ceramics by spark plasma sintering based on the powder bed technology. Materials Science and Engineering of Powder Metallurgy, 2023, 28(2): 113-119.

链接本文:

http://pmbjb.csu.edu.cn/CN/10.19976/j.cnki.43-1448/TF.2022083 或 http://pmbjb.csu.edu.cn/CN/Y2023/V28/I2/113

[1] THOMPSON D.Tough cookery[J]. Nature, 1997, 389(6652): 675-677.
[2] FUMFSCHILLING S, FETT T, HOFFMANN M J, et al.Mechanisms of toughening in silicon nitrides: the roles of crack bridging and microstructure[J]. Acta Materialia, 2011, 59(10): 3978-3989.
[3] XU W W, YIN Z B, YUAN J T, et al.Reliability prediction of a microwave sintered Si₃N₄-based composite ceramic tool[J]. Ceramics International, 2021, 47(12): 16737-16745.
[4] 刘杰, 蒋强国. 含三元烧结助剂的氮化硅陶瓷刀具切削性能研究[J]. 陶瓷学报, 2018, 39(4): 487-491.
LIU Jie, JIANG Qiangguo.Cutting performance of silicon nitride ceramic tool containing ternary sintering additives[J]. Journal of Ceramics. 2018, 39(4): 487-491.
[5] BHUSHAN B, SIBLEY L B.Silicon nitride rolling bearings for extreme operating conditions[J]. American Society of Lubrication Engineers Transactions, 1982, 25(4): 417-428.
[6] 丁泽良, 曾晓红, 吴吉平, 等. 氮化硅陶瓷水煤浆喷嘴的损坏机理[J]. 硅酸盐学报, 2008, 36(S1): 63-66.
DING Zeliang, ZENG Xiaohong, WU Jiping, et al.Failure mechanism of Si₃N₄ ceramic nozzles in coal water slurry industrial boilers[J]. Journal of the Chinese Ceramic Society. 2008, 36(S1): 63-66.
[7] 武振飞, 王跃超, 陆丽芳, 等. 无压烧结氮化硅陶瓷的物理性能研究[J]. 硅酸盐通报, 2022, 41(5): 1782-1787.
WU Zhenfei, WANG Yuechao, LU Lifang, et al.Physical properties of silicon nitride ceramics by pressureless sintering[J]. Bulletin of the Chinese Ceramic Society. 2022, 41(5): 1782-1787.
[8] 周宇章, 魏万鑫, 罗嗣春, 等. 添加TiO₂对Si₃N₄陶瓷刀具切削性能的影响[J]. 机械工程材料, 2022, 46(5): 64-69, 76.
ZHOU Yuzhang, WEI Wanxin, LUO Sichun, et al.Effect of TiO₂ addition on cutting performance of Si₃N₄ ceramic cutting tool[J]. Materials for Mechanical Engineering. 2022, 46(5): 64-69, 76.
[9] LUO S C, GUO W M, PLUCKNETT K, et al.Improved toughness of spark-plasma-sintered Si₃N₄ ceramics by adding HfB₂[J]. Ceramics International, 2021, 47(6): 8717-8721.
[10] LEE C H, LU H H, WANG C A, et al.Effect of heating rate on spark plasma sintering of a nanosized β-Si₃N₄-based powder[J]. Journal of the American Ceramic Society, 2011, 94(4): 1182-1190.
[11] WALKER L S, MAROTTO V R, RAFIEE M A, et al.Toughening in graphene ceramic composites[J]. American Chemical Society Nano, 2011, 5(4): 3182-3190.
[12] TATARKO P, LOJANOVA S, DUSZA J, et al.Influence of various rare-earth oxide additives on microstructure and mechanical properties of silicon nitride based nanocomposites[J]. Materials Science and Engineering A, 2010, 527(18/19): 4771-4778.
[13] VOISIN T, MONCHOUX J P, DURAND L, et al.An innovative way to produce γ-TiAl blades: spark plasma sintering[J]. Advanced Engineering Materials, 2015, 17(10): 1408-1413.
[14] MANIÈRE C, DURAND L, WEIBEL A, et al. Spark- plasma-sintering and finite element method: from the identification of the sintering parameters of a submicronic α-alumina powder to the development of complex shapes[J]. Acta Materialia, 2016, 102: 169-175.
[15] MANIÈRE C, DURAND L, WEIBEL A, et al. A sacrificial material approach for spark plasma sintering of complex shapes[J]. Scripta Materialia, 2016, 124: 126-128.
[16] MANIÈRE C, NIGITO E, DURAND L, et al. Spark plasma sintering and complex shapes: the deformed interfaces approach[J]. Powder Technology, 2017, 320: 340-345.
[17] HOCQUET S, DUPONT V, CAMBIER F, et al.Densification of complex shape ceramics parts by SPS[J]. Journal of the European Ceramic Society, 2020, 40(7): 2586-2596.
[18] 中国国家标准化管理委员会. 精细陶瓷室温硬度试验方法: GB/T 16534—2009[S]. 北京: 中国标准出版社, 2009.
Standardization Administration of China. Fine ceramics test method for hardness of monolithic ceramics at room temperature: GB/T 16534—2009[S]. Beijing: Standared Press of China, 2009.
[19] EVANS A G, CHARLES E A, Fracture toughness determinations by indentation[J]. Journal of the American Ceramic Society, 1976, 59(7/8): 3710-372.
[20] YU J J, WEI W X, GUO W M, et al.Enhanced mechanical properties of Si₃N₄ ceramics with ZrB₂-B binary additives prepared at low temperature[J]. Journal of the European Ceramic Society, 2019, 39(15): 5102-5105.
[21] TATARKO P, LOJANOVA S, DUSZA J.et al.Influence of various rare-earth oxide additives on microstructure and mechanical properties of silicon nitride based nanocomposites[J]. Materials Science and Engineering A, 2010, 527(18/19): 4771-4778.