纳米颗粒增强非晶/纳米晶Ni-P/Ni-W-NbC复合涂层的耐磨及耐蚀性能

doi:10.19976/j.cnki.43-1448/TF.2025065

摘要
图/表
参考文献
相关文章 (10)

全文: PDF (1071 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要为突破传统镀层在强度、耐磨性与耐蚀性协同提升方面的瓶颈,本研究采用脉冲电沉积技术制备Ni-P/Ni-W-NbC纳米复合涂层,并采用扫描电子显微镜、能量色散谱仪、X射线衍射仪等系统研究了NbC纳米颗粒质量浓度对涂层微观结构及性能的影响。结果表明：NbC可通过异质形核显著细化Ni-W涂层晶粒,并在质量浓度阈值(1 g/L)下实现了最佳弥散分布,此时涂层综合性能最优,其显微硬度(HV)达峰值 (1 123.2),摩擦因数最低(0.16),磨损率显著降低。NbC纳米颗粒的质量浓度为1 g/L时,涂层晶粒尺寸最小、结构最致密,NbC通过固溶强化、晶界钉扎及降低孔隙率协同优化了涂层的微观结构。适量NbC (1 g/L)能显著提升涂层在质量分数为3.5%的NaCl溶液中的耐蚀性,表现为电荷转移电阻增大和腐蚀电流密度降低。但过量NbC因颗粒团聚诱发微裂纹和结构缺陷,导致涂层力学性能与耐蚀性能下降。研究阐明了脉冲电沉积中NbC与γ-Ni-W涂层的界面协同强化机制,为开发高硬度、低摩擦且耐蚀的梯度功能涂层提供了理论依据和技术途径。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	齐昌浩
	罗忆
	刘佳晨
	高泽坤
	张敔婷
	徐义库

关键词 ： Ni-P/Ni-W涂层, 脉冲电沉积, NbC纳米颗粒, 耐磨性, 耐蚀性

Abstract：To overcome the bottleneck of synergistic enhancement in strength, wear resistance, and corrosion resistance of traditional coatings, this study employed pulse electrodeposition to prepare Ni-P/Ni-W-NbC nanocomposite coatings. The effects of NbC nanoparticle mass concentration on the microstructure and properties of the coatings were systematically investigated using scanning electron microscope, energy dispersive spectroscope, and X-ray diffractometer. The results indicate that NbC significantly refines the grains of the Ni-W coating through heterogeneous nucleation, achieving optimal dispersive distribution at a mass concentration threshold of 1 g/L. At this mass concentration, the coating exhibits optimal comprehensive performance with a peak microhardness (HV) of 1 123.2, the lowest friction factor of 0.16, and a significantly reduced wear rate. When the NbC nanoparticle mass concentration is 1 g/L, the coating possesses the finest grain size and the densest structure. NbC synergistically optimizes the microstructure of the coating through solid solution strengthening, grain boundary pinning, and reduced porosity. An appropriate amount of NbC (1 g/L) significantly enhances the corrosion resistance of the coating in a NaCl solution with a mass fraction of 3.5%, manifested by an increased charge transfer resistance and a decreased corrosion current density. However, excessive NbC leads to particle agglomeration, inducing microcracks and structural defects, which degrade the mechanical properties and corrosion resistance of the coating. This study elucidates the interfacial synergistic strengthening mechanism between NbC and the γ-Ni-W coating during pulse electrodeposition, providing a theoretical basis and technical pathway for developing gradient functional coatings with high hardness, low friction, and excellent corrosion resistance.

Key words： Ni-P/Ni-W coating pulse electrodeposition NbC nanoparticle wear resistance corrosion resistance

收稿日期: 2025-08-11 出版日期: 2026-01-06

ZTFLH:	TG146.21
	TG174.441

基金资助:陕西省重点研发计划资助项目(2025CY-YBXM-132); 长安大学创新与创业培训计划资助项目(S202510710363,2025 10710001)

通讯作者: 徐义库,教授,博士。电话：15029189267;E-mail: xuyiku23@hotmail.com

引用本文:

齐昌浩, 罗忆, 刘佳晨, 高泽坤, 张敔婷, 徐义库. 纳米颗粒增强非晶/纳米晶Ni-P/Ni-W-NbC复合涂层的耐磨及耐蚀性能[J]. 粉末冶金材料科学与工程, 2025, 30(6): 524-536.
QI Changhao, LUO Yi, LIU Jiachen, GAO Zekun, ZHANG Yuting, XU Yiku. Wear and corrosion resistance of nanoparticle-reinforced amorphous/nanocrystalline Ni-P/Ni-W-NbC composite coatings. Materials Science and Engineering of Powder Metallurgy, 2025, 30(6): 524-536.

链接本文:

http://pmbjb.csu.edu.cn/CN/10.19976/j.cnki.43-1448/TF.2025065 或 http://pmbjb.csu.edu.cn/CN/Y2025/V30/I6/524

[1] ZHANG Z F, HE Y, BAI Y, et al.Influence of iron element on the structure and corrosion resistance of Ni-P coatings in different corrosive environments[J]. Colloids and Surfaces A: Physicochemical and Engineering Aspects, 2022, 655: 130100.
[2] XU X K, ZHANG T F, HUANG W J, et al.Degradation of the Cr₂O₃ layer protectiveness caused by grain refinement during high-temperature oxidation of Cr coatings[J]. Materials Today Communications, 2024, 38: 108442.
[3] GAO M Y, PEI Z L, SONG G H, et al.Wear resistance of Ni/nano-Al₂O₃ composite coatings by brush electroplating[J]. Journal of Materials Science, 2024, 59(16): 7009-7027.
[4] BADIHEHAGHDAM M, KHOIE S M M, KHAST F, et al. Mechanical properties and electrochemical behavior of electroless Ni-P-AlN nanocomposite coating[J]. Metals and Materials International, 2022, 28(6): 1372-1385.
[5] 常帅卿, 甘雪萍, 刘超强. 电共沉积法制备铜铁合金及其表征[J]. 粉末冶金材料科学与工程, 2024, 29(2): 139-150.
CHANG Shuaiqing, GAN Xueping, LIU Chaoqiang.Preparation and characterization of Cu-Fe alloy by electric co-deposition[J]. Materials Science and Engineering of Powder Metallurgy, 2024, 29(2): 139-150.
[6] ALLAHDADI A, RASTEGARI S, KARAZMOUDEH N J.The influence of pulse plating parameters on the structure and corrosion behavior of Ni-W-TiC nanocomposite coatings[J]. Journal of Materials Engineering and Performance, 2025, 34(7): 6253-6264.
[7] YANG G Y, PENG S W, LI Z M, et al.Factors affecting SiC-ZrO₂MoSi₂/Ni antioxidation coating made by composite plating on carbon fibres[J]. Advances in Applied Ceramics, 2019, 118(7): 387-394.
[8] MOHAMED S S M, NIKOLIĆ N D, VUKSANOVIĆ M M, et al. Hardness and wettability characteristics of electrolytically produced copper composite coatings reinforced with layered double oxide (Fe/Al LDO) nanoparticles[J]. Coatings, 2024, 14(6): 740.
[9] CHENG X Y, HE Y, SONG R X, et al.Study of mechanical character and corrosion properties of La₂O₃ nanoparticle reinforced Ni-W composite coatings[J]. Colloids and Surfaces A: Physicochemical and Engineering Aspects, 2022, 652: 129799.
[10] XIA F F, LI Q, MA C Y, et al.Preparation and characterization of Ni-AlN nanocoatings deposited by magnetic field assisted electrodeposition technique[J]. Ceramics International, 2020, 46(2): 2500-2509.
[11] JIN P, SUN C F, ZHANG Z H, et al.Fabrication of the Ni-W-SiC thin film by pulse electrodeposition[J]. Surface and Coatings Technology, 2020, 392: 125738.
[12] CUI W, ZHANG Y H, SONG R X, et al.Ultrasonic assisted pulse electrodeposited Ni-doped TiN coatings[J]. Ceramics International, 2018, 44(12): 14767-14773.
[13] GÓRAL A, CZEPPE T, BERENT K. Oxidation behaviour of thin Ni/Al₂O₃ nanocomposite coatings electrodeposited on steel substrate[J]. Surface and Coatings Technology, 2019, 369: 95-104.
[14] HUANG S G, VLEUGELS J, MOHRBACHER H, et al.Microstructure and tribological performance of NbC-Ni cermets modified by VC and Mo₂C[J]. International Journal of Refractory Metals and Hard Materials, 2017, 66: 188-197.
[15] JIA W R, GONG Y P, ZHENG K, et al.Microstructure evolution, mechanical and abrasive wear properties of NiCrSiB-SiC composite coatings prepared on 16Mn low-carbon steel by Ni-based alloy catalyzed SiC decomposition[J]. Surface and Coatings Technology, 2023, 473: 130022.
[16] LI X R, LONG Y, GUO Z X, et al.Effect of nano-multilayered ZrN/TiAlN hard coating as the interlayer on the microstructure, mechanical properties, and wear resistance[J]. Ceramics International, 2024, 50(22): 46831-46843.
[17] LIAO Z Q, ZHONG F P, ZHANG Z Q, et al.Comparative study on the wear resistance and corrosion resistance of NiW and NiCoW composite coatings with micro- and nano-SiC particles[J]. Materials Today Communications, 2022, 33: 104769.
[18] SURANI-YANCHESHMEH H, GHORBANI M.Corrosion studies on pulse reverse Ni-Mo coatings electrodeposited on Cu substrate[J]. Electrochimica Acta, 2024, 478: 143828.
[19] GUO C Y, FANG Y N, WU B, et al.Ni-P nanoglass prepared by multi-phase pulsed electrodeposition[J]. Materials Research Letters, 2017, 5(5): 293-299.
[20] MA C Y, HE H X, XIA F F, et al.Effect of pulse electrodeposition mode on microstructures and properties of Ni-TiN composite coatings[J]. Coatings, 2024, 14(11): 1384.
[21] WASEKAR N P, VERULKAR S, VAMSI M V N, et al. Influence of molybdenum on the mechanical properties, electrochemical corrosion and wear behavior of electrodeposited Ni-Mo alloy[J]. Surface and Coatings Technology, 2019, 370: 298-310.
[22] PINATE S, GHASSEMALI E, ZANELLA C.Strengthening mechanisms and wear behavior of electrodeposited Ni-SiC nanocomposite coatings[J]. Journal of Materials Science, 2022, 57(35): 16632-16648.
[23] FAYYAZ O, FARHAN M, BAGHERIFARD S, et al.Impact of calcium zirconate nanoparticles on the mechanical and anti-corrosion properties of Ni-P coatings[J]. Materials Chemistry and Physics, 2024, 318: 129294.
[24] YUAN M, JIANG X, LIU Y T, et al.NMP limits silver particle size to solve deposited film breakup problems[J]. AIP Advances, 2024, 14(4): 045312.
[25] XU Y K, LIANG B J, GAO Y, et al.Pulse electrodeposition of a duplex-layer structured composite nickel-based coating with improved corrosion and abrasion resistance[J]. Ceramics International, 2024, 50(7): 10515-10524.
[26] YE M C, DING T T, ZHOU H, et al.Nucleation and growth mechanism of electrodeposited Ni-W alloy[J]. Transactions of Nonferrous Metals Society of China, 2021, 31(6): 1842-1852.
[27] CHEN L, ZHANG G, ZHOU G, et al.In situ visual observation of surface energy-controlled heterogeneous nucleation of metal nanocrystals[J]. Small, 2024, 20(36): 2401674.
[28] PONTE H A, GOMES A C T, MAUL A M, et al. Voltammetric anodic dissolution (VAD) applied to the quantitative analysis of coating discontinuities-influence of electrodeposition parameters[J]. Journal of Applied Electrochemistry, 2004, 34: 147-150.
[29] MONGKOLSUTTIRAT K, SMYTH J R, MCLEAN M, et al.The effects of solid solution and oxide dispersion alloying on the viscoelastic behavior of Au alloy thin films[J]. Acta Materialia, 2019, 168: 275-286.
[30] GUO S, CHAI C F, HU S H, et al.Effects of nano-CeO₂ particles on the microstructural evolution and tribological performance of laser-deposited Ni45 coatings[J]. Surface and Coatings Technology, 2025, 514: 132539.
[31] KANAGASABAPATHY M, BAPU G N K R, SIVAN R, et al. Galvanostatic cathodic polarization studies on anomalously co-electrodeposited Ni_2-18Co_13-97 solid solution nano films[J]. Surface and Coatings Technology, 2013, 232: 188-197.
[32] XU Y K, FAN M Y, LUO Y Q, et al.Tribology and corrosion properties investigation of a pulse electrodeposition duplex hard-particle-reinforced NiMo nanocomposite coating[J]. Surface and Coatings Technology, 2020, 393: 125797.
[33] VAMSI M V N, WASEKAR N P, SUNDARARAJAN G. Sliding wear of as-deposited and heat-treated nanocrystalline nickel-tungsten alloy coatings[J]. Wear, 2018, 412: 136-143.
[34] LIU Y, ZHENG F, WU Y X, et al.Grain refinement induced friction reduction and anti-wear performances of electrodeposited graphene/Ni composites with low content reduced graphene oxide[J]. Journal of Alloys and Compounds, 2020, 826: 154080.
[35] YOUSEFI E, SHARAFI S, IRANNEJAD A.The structural, magnetic, and tribological properties of nanocrystalline Fe-Ni permalloy and Fe-Ni-TiO₂ composite coatings produced by pulse electro co-deposition[J]. Journal of Alloys and Compounds, 2018, 753: 308-319.
[36] WANG X Y, GAO Z M, ZHANG X L, er al. Microstructure and tribological behavior of SiC and BN(h) reinforced electrodeposited Ni matrix composite coatings[J]. Protection of Metals and Physical Chemistry of Surfaces, 2023, 59(3): 404-412.
[37] LEMYA L, HACHEMI B T, ELHACHMI G T.Microstructural, surface and electrochemical properties of electrodeposited Ni-WC nanocomposites coatings[J]. Main Group Chemistry, 2022, 21(3): 763-772.
[38] BADRNEZHAD R, POURFARZAD H, MADRAM A R, et al.Study of the corrosion resistance properties of Ni-P and Ni-P-C nanocomposite coatings in 3.5 wt% NaCl solution[J]. Russian Journal of Electrochemistry, 2019, 55(4): 272-280.