2025年07月25日 星期五 首页   |   期刊介绍   |   编 委 会   |   投稿指南   |   出版法规   |   出版伦理   |   期刊订阅   |   联系我们   |   留言板   |   广告合作   |   ENGLISH
粉末冶金材料科学与工程  2018, Vol. 23 Issue (3): 274-280    
  工艺技术 本期目录 | 过刊浏览 | 高级检索 |
Al-3P变质Al-18Si合金的显微组织与力学性能
杨威1,2,3, 陆晓旺1,2,3, 刘亚1,2,3, 吴长军1,2,3, 王建华1,2,3, 苏旭平1,2,3
1. 常州大学 材料科学与工程学院,常州 213164;
2. 常州大学 材料科学与工程国家级实验教学示范中心,常州 213164;
3. 江苏省材料表面科学与技术重点实验室,常州 213164
Microstructure and mechanical properties of Al-18Si alloy modified by Al-3P master alloy
YANG Wei1,2,3, LU Xiaowang1,2,3, LIU Ya1,2,3, WU Changjun1,2,3, WANG Jianhua1,2,3, SU Xuping1,2,3
1. School of Material Science and Engineering, Changzhou University, Changzhou 213164, China;
2. National Experimental Teaching Demonstration Center of Materials Science and Engineering, Changzhou University, Changzhou 213164, China;
3. Jiangsu Key Laboratory of Materials Surface Science and Technology, Changzhou 213164, China
全文: PDF (1149 KB)   HTML (1 KB) 
输出: BibTeX | EndNote (RIS)      
摘要 用Al-3P作为变质剂对Al-18Si合金进行变质处理,利用光学显微镜、Image Pro Plus 6.0软件、扫描电镜和万能电子试验机等研究变质剂加入量w(Al-3P)(0~1.0%)和变质温度(750~850 ℃)对合金显微组织与拉伸性能的影响。结果表明,变质处理后,初晶硅的尺寸减小,面积分数增大。当变质温度为800 ℃时,随w(Al-3P)增加,初晶硅的尺寸先减小后增大,初晶硅的面积分数先增大后减小,w(Al-3P)为0.6%时初晶硅尺寸最小,平均尺寸为14 μm,w(Al-3P)为0.8%时初晶硅面积分数达到最大值14.4%。当w(Al-3P)为0.8%时,随变质温度升高,Al-18Si合金中的初晶硅面积分数减小,初晶硅尺寸先减小后增大,变质温度为800℃时初晶硅尺寸最小,约为15 μm。与未变质的Al-18Si合金相比,在800 ℃加入0.8%Al-3P变质处理后,合金的抗拉强度和伸长率分别提高17.6%和109%,拉伸断口呈现明显的韧性断裂特征。
服务
把本文推荐给朋友
加入我的书架
加入引用管理器
E-mail Alert
RSS
作者相关文章
杨威
陆晓旺
刘亚
吴长军
王建华
苏旭平
关键词 过共晶铝硅合金变质处理初晶硅显微组织力学性能    
Abstract:Al-18Si alloy was modified by Al-3P master alloy. The effects of adding amount of alterant w(Al-3P)(0-1.0%) and modification temperature (750-850 ℃) on microstructures and tensile properties of the alloy were investigated by optical microscope (OP), Image Pro Plus 6.0, scanning electron microscopy (SEM) and universal testing machine. The results show that the size of primary Si decreases and its area fraction increases after modification. With the increase of w(Al-3P), the size of primary Si first decreases and then increases, and the area fraction of primary Si first increases and then decreases when Al-18Si alloy was modified at 800 ℃.When the adding amount of alterant w(Al-3P) is 0.6%, the size of primary Si is the smallest, and the average size is 14 μm. When the adding amount of w(Al-3P) is 0.8%, the area fraction of primary Si reaches the maximum of 14.4%. When the adding amount of w(Al-3P) is 0.8%, the area fraction of primary Si in Al-18Si alloy decreases with the increase of modification temperature. The size of primary Si decreases first and then increases. The size of primary Si is the smallest of 15 μm when the alloy is modified at 800 ℃. Compared with unmodified Al-18Si alloy, the tensile strength and elongation of Al-18Si alloy increase by 17.6% and 109% respectively after modified with w(Al-3P)0.8% at 800 ℃. The fracture mode of the modified Al-18Si alloy is ductile fracture.
Key wordshypereutectic Al-Si alloy    modification    primary Si    microstructure    mechanical properties
收稿日期: 2017-10-30      出版日期: 2019-07-12
ZTFLH:  TG292  
基金资助:国家自然科学基金资助项目(51571039)
通讯作者: 王建华,教授,博士。电话:15961165336;E-mail: wangjh@cczu.edu.cn   
引用本文:   
杨威, 陆晓旺, 刘亚, 吴长军, 王建华, 苏旭平. Al-3P变质Al-18Si合金的显微组织与力学性能[J]. 粉末冶金材料科学与工程, 2018, 23(3): 274-280.
YANG Wei, LU Xiaowang, LIU Ya, WU Changjun, WANG Jianhua, SU Xuping. Microstructure and mechanical properties of Al-18Si alloy modified by Al-3P master alloy. Materials Science and Engineering of Powder Metallurgy, 2018, 23(3): 274-280.
链接本文:  
http://pmbjb.csu.edu.cn/CN/     或     http://pmbjb.csu.edu.cn/CN/Y2018/V23/I3/274
版权所有 © 《粉末冶金材料科学与工程》编辑部
地址:长沙市麓山南路中南大学粉末冶金研究院 邮编:410083 电话:0731-88877163 邮箱:pmbjb@csu.edu.cn
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn