CuCoCrNi/金刚石复合材料超快速高温烧结致密化行为

doi:10.19976/j.cnki.43-1448/TF.2025043

摘要
图/表
参考文献
相关文章 (9)

全文: PDF (974 KB) HTML (0 KB)
输出: BibTeX | EndNote (RIS)

摘要本文采用超快速高温烧结技术制备以CuCoCrNi多主元合金为黏结相的金刚石复合材料,借助X射线衍射仪、扫描电镜、拉曼衍射仪、摩擦磨损实验等手段,研究烧结参数对复合材料金刚石石墨化程度及致密化行为的影响。结果表明：采用合适的工艺参数,超快速高温烧结技术可以在短时间内获得金刚石石墨化程度低(I_G/I_D=0.201 4)、摩擦因数低(μ=0.06)且相对密度达到91.22%的CuCoCrNi/金刚石复合材料。高电流密度产生的焦耳热以及局部热效应能显著提高烧结驱动力,促进基体中的Cr与金刚石表面结合形成界面层,有利于复合材料致密化。但过高能量输入会引发金刚石颗粒团聚及严重的金刚石石墨化(I_G/I_D>1.0),降低Cr元素与金刚石颗粒表面的亲和度和界面结合强度,从而降低复合材料的致密度及摩擦性能(μ>0.1)。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	李林
	杨紫涵
	王若冲
	刘咏

关键词 ：超快速高温烧结, 多主元合金, 金刚石复合材料, 致密化行为, 摩擦性能

Abstract：In this study, ultrafast high-temperature sintering was employed to fabricate diamond composites using CuCoCrNi multi-principal element alloy as the bonding phase. The effects of sintering parameters on the degree of diamond graphitization and densification behavior were investigated with X-ray diffractometer, scanning electron microscope, Raman spectroscope, and friction experiments. The results demonstrate that ultrafast high-temperature sintering can produce CuCoCrNi/diamond composites with low graphitization (I_G/I_D=0.201 4), low friction factor (μ=0.06), and relative density of 91.22% in a short time by adopting suitable process parameters. Joule heating generated by high current density and localized thermal focusing significantly enhance the sintering driving force, promoting the bonding of Cr in the matrix with the diamond surface to form an interface layer is conducive to the densification of the composites. However, too high energy input can cause diamond particle agglomeration and severe diamond graphitization (I_G/I_D>1.0), reduce the affinity and the interfacial bonding strength between Cr element and diamond particle surface, leading to the decrease of density and friction properties (μ>0.1) of diamond composites.

Key words： ultrafast high-temperature sintering multi-principal element alloy diamond composite densification behavior friction property

收稿日期: 2025-04-30 出版日期: 2026-01-06

ZTFLH:

TB331

基金资助:国家重点研发计划资助项目(2021YFB3701800)

通讯作者: 刘咏,教授,博士。电话：0731-88879422; E-mail: yonliu@csu.edu.cn

引用本文:

李林, 杨紫涵, 王若冲, 刘咏. CuCoCrNi/金刚石复合材料超快速高温烧结致密化行为[J]. 粉末冶金材料科学与工程, 2025, 30(6): 514-523.
LI Lin, YANG Zihan, WANG Ruochong, LIU Yong. Densification behavior of CuCoCrNi/diamond composites under ultrafast high-temperature sintering. Materials Science and Engineering of Powder Metallurgy, 2025, 30(6): 514-523.

链接本文:

http://pmbjb.csu.edu.cn/CN/10.19976/j.cnki.43-1448/TF.2025043 或 http://pmbjb.csu.edu.cn/CN/Y2025/V30/I6/514

[1] YUAN Q B, YAO F Z, CHENG S D, et al.Bioinspired hierarchically structured all-inorganic nanocomposites with significantly improved capacitive performance[J]. Advanced Functional Materials, 2020, 30(23): 2000191.
[2] YAO F Z, YUAN Q B, WANG Q, et al.Multiscale structural engineering of dielectric ceramics for energy storage applications: from bulk to thin films[J]. Nanoscale, 2020, 12(33): 17165-17184.
[3] ZHANG J L, SONG B, WEI Q S, et al.A review of selective laser melting of aluminum alloys: processing, microstructure, property and developing trends[J]. Journal of Materials Science & Technology, 2019, 35(2): 270-284.
[4] MISHRA R R, SHARMA A K.Microwave-material interaction phenomena: heating mechanisms, challenges and opportunities in material processing[J]. Composites Part A: Applied Science and Manufacturing, 2016, 81: 78-97.
[5] GUILLON O, GONZALEZ-JULIAN J, DARGATZ B, et al.Field-assisted sintering technology/spark plasma sintering: mechanisms, materials, and technology developments[J]. Advanced Engineering Materials, 2014, 16(7): 830-849.
[6] COLOGNA M, RASHKOVA B, RAJ R.Flash sintering of nanograin zirconia in <5 s at 850 ℃[J]. Journal of the American Ceramic Society, 2010, 93(11): 3556-3559.
[7] WANG C W, PING W W, BAI Q, et al.A general method to synthesize and sinter bulk ceramics in seconds[J]. Science, 2020, 368(6490): 521-526.
[8] MISHRA T P, WANG S F, LENSER C, et al.Ultra-fast high-temperature sintering of strontium titanate[J]. Acta Materialia, 2022, 231: 117918.
[9] LIU Q, GUO S C, LENG S L, et al.Preparation and property of porous calcium silicate ceramic by two-step ultrafast high-temperature sintering[J]. International Journal of Applied Ceramic Technology, 2024, 21(5): 3346-3354.
[10] WANG C W, ZHONG W, PING W W, et al.Rapid synthesis and sintering of metals from powders[J]. Advanced Science, 2021, 8(12): 2004229.
[11] LIBRAGA I F, SCHNEIDER A D, BRAM M, et al.Ultrafast high-temperature sintering (UHS) of Ti and TiNb alloys[J]. The Journal of The Minerals, Metal & Materials Society, 2024, 77: 1765-1773.
[12] WANG Y G, LIU B, SONG J Y, et al.Study on the wear mechanism of PCD tools in high-speed milling of Al-Si alloy[J]. Advanced Materials Research, 2011, 381: 16-19.
[13] TZE-PIN L, HOOD M, COOPER G A, et al.Wear and failure mechanisms of polycrystalline diamond compact bits[J]. Wear, 1992, 156(1): 133-150.
[14] SCHUBERT T, TRINDADE B, WEIßGÄRBER T, et al. Interfacial design of Cu-based composites prepared by powder metallurgy for heat sink applications[J]. Materials Science and Engineering A, 2008, 475(1/2): 39-44.
[15] SCHUBERT T, CIUPIŃSKI Ł, ZIELIŃSKI W, et al. Interfacial characterization of Cu/diamond composites prepared by powder metallurgy for heat sink applications[J]. Scripta Materialia, 2008, 58(4): 263-266.
[16] WANG Y L, DUAN K Y, WANG K K, et al.Structure and thermal properties of layered Ti-clad diamond/Cu composites prepared by SPS and HP[J]. Rare Metal Materials and Engineering, 2018, 47(7): 2011-2016.
[17] 高阳, 肖海波, 刘咏, 等. 界面反应对Cu₃₅Ni₂₅Co₂₅Cr₁₅多主元合金/金刚石复合材料磨损性能的影响[J]. 复合材料学报, 2023, 40(2): 1105-1117.
GAO Yang, XIAO Haibo, LIU Yong, et al.Effect of interfacial reaction on the wear properties of Cu₃₅Ni₂₅Co₂₅Cr₁₅ multi-principal components alloy/diamond composites[J]. Acta Materiae Compositae Sinica, 2023, 40(2): 1105-1117.
[18] LI R D, YUAN T C, LIU X J, et al.Enhanced atomic diffusion of Fe-Al diffusion couple during spark plasma sintering[J]. Scripta Materialia, 2016, 110: 105-108.
[19] CHEN C M, CHEN S W.Electric current effects on Sn/Ag interfacial reactions[J]. Journal of Electronic Materials, 1999, 28(7): 902-906.
[20] RUDINSKY S, GAUVIN R, BROCHU M.The effects of applied current on one-dimensional interdiffusion between copper and nickel in spark plasma sintering[J]. Journal of Applied Physics, 2014, 116(15): 154901.
[21] RATZKER B, SOKOL M, KALABUKHOV S, et al.Compression creep of copper under electric current studied by a spark plasma sintering (SPS) apparatus[J]. Materials Science and Engineering A, 2018, 712: 424-429.
[22] DENG S H, LI R D, YUAN T C, et al.Direct current-enhanced densification kinetics during spark plasma sintering of tungsten powder[J]. Scripta Materialia, 2018, 143: 25-29.
[23] WANG J, RAJ R.Activation energy for the sintering of two-phase alumina/zirconia ceramics[J]. Journal of the American Ceramic Society, 1991, 74(8): 1959-1963.
[24] ÁLVAREZ I, TORRECILLAS R, SOLIS W, et al.Microstructural design of Al₂O₃-SiC nanocomposites by spark plasma sintering[J]. Ceramics International, 2016, 42(15): 17248-17253.
[25] LEE G, OLEVSKY E A, MANIÈRE C, et al. Effect of electric current on densification behavior of conductive ceramic powders consolidated by spark plasma sintering[J]. Acta Materialia, 2018, 144: 524-533.