|
|
|
| Properties of three-dimensional (3D) graphene-reinforced copper matrix composites by powder metallurgy method |
| YI Chunqiang1,2, YIN Cailiu1, LIU Chunxuan2, WEN Guofu1, WANG Xiufei1 |
1. Institute of Friction Materials, Guangxi University for Nationalities, Nanning 530006, China;
2. Hunan Xiangtou Jingtian of Science and Technology Limited Liability Company, Changsha 410008, China |
|
|
|
|
Abstract The 0-0.4% (mass fraction) 3D graphene was added as a reinforcement in Cu-5%Sn alloy. The 3D graphene/Cu-5%Sn composites were prepared via powder metallurgy method. The density, resistivity, tensile strength, impact strength, Brinell hardness and friction and wear properties were measured. The results show that with increasing 3D graphene content, the density and tensile strength of 3D graphene/Cu-5%Sn composites decrease, and the resistivity increase slightly, the wear value increases. As the braking speed increases, the friction coefficient decreases. The composite with 0.4% graphene has the best stable friction coefficient. Compared with Cu-5%Sn matrix, when the content of 3D graphene is 0.2%, the maximum impact strength is 32.5 J/cm2,which is increased by 57.0%. When the content of 3D graphene is 0.1%, the Brinell hardness (HBW) and elongation are 122.0 and 11.52%, respectively, which is increased by 22.0% and 10.5% for Cu-5%Sn alloy. The fracture morphology of composite appears a dimple pattern with typical features of plastic fracture.
|
|
Received: 24 April 2019
Published: 14 November 2019
|
|
|
|
|
|
[1] ZHANG P, JIE J, GAO Y, et al.Preparation and properties of TiB2 particles reinforced Cu-Cr matrix composite[J]. Materials Science and Engineering A, 2015, 642: 398-405.
[2] RAJKOVIC V, BOZIC D, STASIC J, et al.Processing characterization and properties of copper-based composites strengthened by low amount of alumina particles[J]. Powder Technology, 2014, 268: 392-400.
[3] 刘云圻. 石墨烯从基础到应用[M]. 北京: 化学工业出版社, 2019: 2-6.
LIU Yunyin.Graphene: From Basics to Applications[M]. Beijing: Chemical Industry Press, 2019: 2-6.
[4] PAVITHRA C L P, SARADA B V, PAJULAPATI K V, et al. A new electrochemical approach for the synthesis of copper- graphene nanocomposite foils with high hardness[J]. Sci Rep, 2014, 4: doi: 10. 1038/srep04049.
[5] LI Jingfu, ZHANG L, XIAO J, et al.Sliding wear behavior of copper-based composites reinforced with grapheme nanosheets and graphite[J]. Transactions of Nonferrous Metals Society of China, 2015, 25(10): 3354-3362.
[6] SHIN S E, CHOI H J, SHIN J H, et al.Strengthening behavior of few-layered graphene/aluminum composites[J]. Carbon, 2015, 82: 143-151.
[7] 王禹, 朱传平, 雷霆. 石墨烯增强铝基复合材料的制备及性能[J]. 粉末冶金材料科学与工程, 2018, 23(5): 518-526.
WANG Yu, ZHU Chuanping, LEI Ting.Preparation and properties of graphene reinforced aluminum matrix composites[J]. Materials Science and Engineering of Powder Metallurgy, 2018, 23(5): 518-526.
[8] 晏伯武. 三维石墨烯的制备和应用研究[J]. 陶瓷学报, 2018, 39(4): 380-385.
YAN Bowu.Preparation and application of three-dimensional graphene[J]. Journal of Ceramics, 2018, 39(4): 380-385.
[9] QIAO Z, ZHOU T, KANG J, et al.Three-dimensional interpenetrating network graphene/copper composites with simultaneously enhanced strength, ductility and conductivity[J]. Materials Letters, 2018, 224: 37-41.
[10] XIE Aijuan, DU Jiawen, TAO Feng, et al.Three-dimensional graphene surface-mounted nickel-based metal organic framework for oxygen evolution reaction[J]. Electrochimica Acta, 2019, 305: 338-348.
[11] 黄培云. 粉末冶金原理[M]. 北京: 冶金工业出版社, 1997: 265.
HUANG Peiyun.Power Metallurgy Principle[M]. Beijing: Metallurgical Industry Press, 1997: 265.
[12] 曾竟成. 复合材料理化性能[M]. 长沙: 国防科技大学出版社, 1998: 96.
ZENG Jingcheng.Physical and Chemical Properties of Composite Materials[M]. Changsha: National University of Defence Technology Press, 1998: 96.
[13] 姚龙辉. 石墨烯增强铜基复合材料的制备和性能研究[D]. 哈尔滨: 哈尔滨理工大学, 2017.
YAO Longhui.Fabrication and properties of graphene reinforced copper matrix composites[D]. Harbin: Harbin University of Science and Technology, 2017.
[14] 余亚岚, 袁楠, 江丹露, 等. 镍与石墨含量对新型铜基粉末冶金受电弓滑板材料性能的影响[J]. 粉末冶金材料科学与工程, 2015, 20(3): 419-424.
YU Yalan, YUAN Nan, JIANG Danlu, et al.Effects of nickel and graphite content on new copper matrix P/M materials for pantoraraph slider[J]. Materials Science and Engineering of Powder Metallurgy, 2015, 20(3): 419-424.
[15] 温诗铸, 黄平, 田煜, 等. 摩擦学原理[M]. 北京: 清华大学出版社, 2018: 271-275.
WEN Shizhu, HUANG Ping, TIAN Yu, et al.Principles of Tribology[M]. Beijing: Tsinghua University Press, 2018: 271-275. |
|
|
|
2019, Vol. 24 
