首页   |   期刊介绍   |   编 委 会   |   投稿指南   |   出版法规   |   出版伦理   |   期刊订阅   |   联系我们   |   留言板   |   广告合作   |   ENGLISH
工艺技术

织构对激光定向能量沉积Ni50.8Ti形状记忆合金超弹性的影响

  • 吴慧婷 ,
  • 李瑞迪 ,
  • 康景涛 ,
  • 郑聃
展开
  • 中南大学 粉末冶金国家重点实验室,长沙 410083

收稿日期: 2023-12-08

  修回日期: 2024-01-30

  网络出版日期: 2024-03-26

基金资助

湖南省创新平台与人才计划(2022RC3033)

Effect of texture on the superelasticity of Ni50.8Ti shape memory alloy for laser directed energy deposition

  • WU Huiting ,
  • LI Ruidi ,
  • KANG Jingtao ,
  • ZHENG Dan
Expand
  • State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083, China

Received date: 2023-12-08

  Revised date: 2024-01-30

  Online published: 2024-03-26

摘要

NiTi形状记忆合金由于热弹性马氏体相变而表现出优异的超弹性和形状记忆效应,被广泛应用在医疗器械、航空航天等领域。采用激光定向能量沉积工艺制备Ni50.8Ti形状记忆合金,通过室温压缩实验和循环压缩实验分析成形角度对合金超弹性及其稳定性的影响规律,借助X射线衍射分析、电子背散射衍射等表征手段分析不同成形角度合金的微观组织和织构特征,进而深入研究微观组织和织构对Ni50.8Ti形状记忆合金超弹性及其稳定性的影响。结果表明:采用激光定向能量沉积制备的Ni50.8Ti形状记忆合金由B2奥氏体相组成,基体成分均匀,无开裂现象。与Y轴呈90°的合金在室温下呈现出最佳的超弹性,0°的合金超弹性最差。同时,45°的合金呈现出强〈112〉织构,90°的合金呈现出强〈110〉织构,强织构合金的超弹性比弱织构(60°)和不利取向(0°)合金的超弹性更好,织构对于Ni50.8Ti形状记忆合金的微观组织和超弹性具有显著的影响。

本文引用格式

吴慧婷 , 李瑞迪 , 康景涛 , 郑聃 . 织构对激光定向能量沉积Ni50.8Ti形状记忆合金超弹性的影响[J]. 粉末冶金材料科学与工程, 2024 , 29(1) : 63 -73 . DOI: 10.19976/j.cnki.43-1448/TF.2023081

Abstract

NiTi shape memory alloy exhibits excellent superelasticity and shape memory effect due to thermoelastic martensitic phase transformation, and is widely used in medical devices, aerospace and other fields. Ni50.8Ti shape memory alloy was prepared by laser directed energy deposition, the influences of forming angle on the superelasticity and stability of the alloy were analyzed by room temperature compression and cyclic compression experiments, the microstructure and texture characteristics of alloys with different forming angles were analyzed by X-ray diffraction analysis, electron backscatter diffraction and other characterization methods, and the influences of microstructure and texture on the superelasticity and stability of Ni50.8Ti shape memory alloy were further studied. The results show that the Ni50.8Ti shape memory alloy prepared by laser directed energy deposition is composed of B2 austenitic phase with uniform matrix composition and no cracking phenomenon. Alloy at 90° Y-axis shows the best superelasticity at room temperature, and the worst superelasticity at 0°. At the same time, the 45° alloy shows a strong 〈112〉 texture and the 90° alloy shows a strong 〈110〉 texture, the superelasticity of the strong texture alloy is better than that of the weak texture (60°) and the unfavorable orientation (0°) alloy, the texture has a significant influence on the microstructure and superelasticity of the Ni50.8Ti shape memory alloy.

参考文献

[1] PARVIZI S, HASHEMI S M, ASGARINIA F, et al.Effective parameters on the final properties of NiTi-based alloys manufactured by powder metallurgy methods: a review[J]. Progress in Materials Science, 2021, 117(7): 100739.
[2] ELAHINIA M H, HASHEMI M, TABESH M, et al.Manufacturing and processing of NiTi implants: a review[J]. Progress in Materials Science, 2012, 57(5): 911-946.
[3] 杜昌海, 李东阳, 朱本银, 等. 高强度高应力循环稳定的HDH多孔NiTi形状记忆合金[J]. 工程科学学报, 2023, 45(12): 2059-2069.
DU Changhai, LI Dongyang, ZHU Benyin, et al.HDH porous NiTi shape memory alloy with high strength and high stress cycle stability[J]. Journal of Engineering Sciences, 2023, 45(12): 2059-2069.
[4] 康景涛, 刘子豪, 郑聃, 等. Ni含量对激光粉末床熔融成形NiTi形状记忆合金显微组织和力学性能的影响[J]. 铸造技术, 2023, 44(7): 649-656.
KANG Jingtao, LIU Zihao, ZHENG Dan, et al.Effect of Ni content on microstructure and mechanical properties of NiTi shape memory alloy formed by laser powder bed melting[J]. Foundry Technology, 2023, 44(7): 649-656.
[5] 王盖世, 左舜贵, 曹军, 等. Ti-Ni超弹合金B2相与R相的氢脆敏感性比较研究[J]. 金属功能材料, 2022, 29(5): 10-17.
WANG Gaishi, ZUO Shungui, CAO Jun, et al.Comparative study on hydrogen embrittlement sensitivity between B2 phase and R phase of Ti-Ni superelastic alloys[J]. Metal Functional Materials, 2022, 29(5): 10-17.
[6] 倪江涛, 周庆军, 衣凤, 等. 激光增材制造技术发展及在航天领域的应用进展[J]. 稀有金属, 2022, 46(10): 1365-1382.
NI Jiangtao, ZHOU Qingjun, YI Feng, et al.Development of laser additive manufacturing technology and its application in aerospace field[J]. Rare Metals, 2022, 46(10): 1365-1382.
[7] 熊强, 连利仙, 胡旺, 等. 增材制造用新型镍基高温合金的设计与开发[J]. 铸造技术, 2023, 44(8): 748-755.
XIONG Qiang, LIAN Lixian, HU Wang, et al.Design and development of new nickel-based superalloys for additive manufacturing[J]. Foundry Technology, 2023, 44(8): 748-755.
[8] 刘旭明, 张大越, 张建, 等. 激光熔丝增材制造低合金钢的微观组织及性能研究[J]. 钢铁钒钛, 2022, 43(1): 119-124.
LIU Xuming, ZHANG Dayue, ZHANG Jian, et al.Study on microstructure and properties of low alloy steel manufactured by laser fuse additive[J]. Iron Steel Vanadium Titanium, 2022, 43(1): 119-124.
[9] 丁红瑜, 武姝婷, 袁康, 等. 增材制造国内外标准研究进展[J]. 中国材料进展, 2020, 39(12): 955-961.
DING Hongyu, WU Shuting, YUAN Kang, et al.Research progress of additive manufacturing standards at home and abroad[J]. Materials Progress in China, 2020, 39(12): 955-961.
[10] SVETLIZKY D, DAS M, ZHENG B, et al.Directed energy deposition (DED) additive manufacturing: physical characteristics, defects, challenges and applications[J]. Materials Today, 2021, 49(5): 271-295.
[11] ROMANENKO D, PRAKASH V J, KUHN T, et al.Effect of DED process parameters on distortion and residual stress state of additively manufactured Ti-6Al-4V components during machining[J]. Procedia CIRP, 2022, 111(3): 271-276.
[12] ANDRADE M F, PEREIRA M V, TEIXEIRA M C, et al.Fatigue life assessment in the very high cycle regime of AISI 316L stainless steel processed by L-DED additive manufacturing[J]. Procedia Structural Integrity, 2022, 42(4): 1008-1016.
[13] NIU P, LI R, FAN Z, et al.Additive manufacturing of TRIP-assisted dual-phases Fe50Mn30Co10Cr10 high-entropy alloy: microstructure evolution, mechanical properties and deformation mechanisms[J]. Materials Science and Engineering A, 2021, 814(2): 141264.
[14] ZHENG D, LI R D, YUAN T C, et al.Comparative study on microstructure and properties of NiTi shape memory alloy by selective laser melting and directed energy deposition[J]. Journal of Central South University, 2021, 28(4): 1028-1042.
[15] WANG Y F, YUE Z F, WANG J.The effect of grain orientation on the tensilecompressive asymmetry of polycrystalline NiTi shape memory alloy[J]. Materialwissenschaft und Werkstofftechnik, 2007, 38(4): 294-298.
[16] LUO J, XU K, LI C, et al.The evolution of dynamic recrystallization and recrystallization texture during isothermal compression of NiTi shape memory alloy[J]. Materials Science and Engineering A, 2021, 820(5): 11873-11875.
[17] TANG W, SHEN Q, YAO X, et al.Effect of grain size on the microstructure and mechanical anisotropy of stress-induced martensitic NiTi alloys[J]. Materials Science and Engineering A, 2022, 849(2): 786-791.
[18] ZHAN J B, WU J Z, MA R J, et al.Effect of microstructure on the superelasticity of high-relative-density Ni-rich NiTi alloys fabricated by laser powder bed fusion[J]. Journal of Materials Processing Technology, 2023, 317(4): 672-677.
[19] 鲁璐青, 刘志义, 夏鹏. 高强度织构对2524铝合金疲劳性能的影响[J]. 粉末冶金材料科学与工程, 2017, 22(3): 307-312.
LU Luqing, LIU Zhiyi, XIA Peng.Effect of high strength texture on fatigue properties of 2524 aluminum alloy[J]. Materials Science and Engineering of Powder Metallurgy, 2017, 22(3): 307-312.
[20] SUN S H, ISHIMOTO T, HAGIHARA K, et al.Excellent mechanical and corrosion properties of austenitic stainless steel with a unique crystallographic lamellar microstructure via selective laser melting[J]. Scripta Materialia, 2019, 159(6): 89-93.
[21] SAFAEI K, ANDANI N T, POORGANJI B, et al.Controlling texture of NiTi alloy processed by laser powder bed fusion: smart build orientation and scanning strategy[J]. Additive Manufacturing Letters, 2023, 5(2): 100126.
[22] CHOI W S, PANG E L, KO W S, et al.Orientation- dependent plastic deformation mechanisms and competition with stress-induced phase transformation in microscale NiTi[J]. Acta Materialia, 2021, 208(6): 116731-116739.
[23] SINHA A, RAJAK D K, SHAIK N B, et al.A review on 4D printing of nickel-titanium smart alloy processing, the effect of major parameters and their biomedical applications[J]. Proceedings of the Institution of Mechanical Engineers Part E-Journal of Process Mechanical Engineering, 2023, 456(3): 674-679.
[24] LU H Z, MA H W, YANG Y, et al.Tailoring phase transformation behavior, microstructure, and superelasticity of NiTi shape memory alloys by specific change of laser power in selective laser melting[J]. Materials Science and Engineering A, 2023, 864(2): 236-243.
[25] 刘伟, 刘成松, 丁小明, 等. 激光粉床增材制造不锈钢中氧化物夹杂调控的研究进展[J]. 钢铁研究学报, 2023, 35(5): 489-503.
LIU Wei, LIU Chengsong, DING Xiaoming, et al.Research progress of oxide inclusion control in laser powder bed additive manufacturing of stainless steel[J]. Journal of Iron and Steel Research, 2023, 35(5): 489-503.
[26] 姜沐池, 任德春, 赵晓彧, 等. 激光扫描速度对Ti-Ni形状记忆合金影响规律研究[J]. 稀有金属材料与工程, 2023, 52(4): 1455-1463.
JIANG Muchi, REN Dechun, ZHAO Xiaoyu, et al.Effect of laser scanning speed on Ti-Ni shape memory alloy[J]. Rare Metal Materials and Engineering, 2023, 52(4): 1455-1463.
[27] LIU Z, ZHAO D, WANG P, et al.Additive manufacturing of metals: microstructure evolution and multistage control[J]. Journal of Materials Science & Technology, 2022, 100(3): 224-236.
[28] HAMILTON R F, BIMBER B A, PALMER T A.Correlating microstructure and superelasticity of directed energy deposition additive manufactured Ni-rich NiTi alloys[J]. Journal of Alloys and Compounds, 2018, 739(4): 712-722.
[29] ZHAO Y, GUO K, SUI X, et al.Nonlinear deformation mechanism of Ni50.8Ti shape memory alloy at different temperatures and strain rates[J]. Journal of Materials Engineering and Performance, 2023, 432(2): 523-527.
[30] KOCKAR B, KARAMAN I, KIM J I, et al.Thermomechanical cyclic response of an ultrafine-grained NiTi shape memory alloy[J]. Acta Materialia, 2008, 56(14): 3630-3646.
[31] KANG G, KAN Q, QIAN L, et al.Ratchetting deformation of super-elastic and shape-memory NiTi alloys[J]. Mechanics of Materials, 2009, 41(2): 139-153.
[32] NORFLEET D M, SAROSI P M, MANCHIRAJU S, et al.Transformation-induced plasticity during pseudoelastic deformation in Ni-Ti microcrystals[J]. Acta Materialia, 2009, 57(12): 3549-3561.
[33] SIMON T, KROEGER A, SOMSEN C, et al.On the multiplication of dislocations during martensitic transformations in NiTi shape memory alloys[J]. Acta Materialia, 2010, 58(5): 1850-1860.
[34] WAITZ T, ANTRETTER T, FISCHER F D, et al.Size effects on the martensitic phase transformation of NiTi nanograins[J]. Journal of the Mechanics and Physics of Solids, 2007, 55(2): 419-444.
[35] SEDMÁK P, SITTNER P, PILCH J, et al. Instability of cyclic superelastic deformation of NiTi investigated by synchrotron X-ray diffraction[J]. Acta Materialia, 2015, 94(5): 257-270.
[36] DELVILLE R, MALARD B, PILCH J, et al.Transmission electron microscopy investigation of dislocation slip during superelastic cycling of Ni-Ti wires[J]. International Journal of Plasticity, 2011, 27(2): 282-297.
[37] XU K F, LUO J, LI C, et al.Mechanisms of stress-induced martensitic transformation and transformation-induced plasticity in NiTi shape memory alloy related to superelastic stability[J]. Scripta Materialia, 2022, 217(7): 112-114.
[38] GALL K, SEHITOGLU H.The role of texture in tension-compression asymmetry in polycrystalline NiTi[J]. International Journal of Plasticity, 1999, 15(1): 69-92.
[39] 熊君媛, 徐波, 康国政. 纳米多晶NiTi形状记忆合金超弹性的晶粒取向依赖性相场研究[J]. 固体力学学报, 2021, 42(6): 671-681.
XIONG Junyuan, XU Bo, KANG Guozheng.Study on grain orientation dependent phase field of superelasticity of nano-polycrystalline NiTi shape memory alloys[J]. Chinese Journal of Solid State Mechanics, 2021, 42(6): 671-681.
[40] CAI S, SCHAFFER J E, YU C, et al.Evolution of intergranular stresses in a martensitic and an austenitic NiTi wire during loading-unloading tensile deformation[J]. Metallurgical and Materials Transactions A, 2015, 46(6): 2476-2490.
文章导航

/

版权所有 © 《粉末冶金材料科学与工程》编辑部
地址:长沙市麓山南路中南大学粉末冶金研究院 邮编:410083 电话:0731-88877163 邮箱:pmbjb@csu.edu.cn
本系统由北京玛格泰克科技发展有限公司设计开发 技术支持:support@magtech.com.cn