连续纤维增强陶瓷基复合材料3D打印：研究进展与挑战

doi:10.19976/j.cnki.43-1448/TF.2024068

Abstract
Figure/Table
References
Related Citation (13)

Download: PDF (2247 KB) HTML (0 KB)
Export: BibTeX | EndNote (RIS)

Abstract Continuous fiber reinforced ceramic matrix composites (CFRCMCs) exhibit low density, high strength, excellent high-temperature stability and chemical stability, which are of significant application in various fields including aerospace, nuclear industry, chemical engineering, and transportation. In recent years, the evolution of 3D printing technology has provided an innovative approach for the shaping of complex and irregular CFRCMCs preforms. However, 3D printing of CFRCMCs remains in its infancy with significant challenges in forming equipment, processes, and principles. Hence, a summary and analysis of the research progress and challenges of the 3D printing of CFRCMCs are of significant value. Firstly, this paper briefly introduces 3D printing technologies; then, research progresses in 3D printing of CFRCMCs, including thermoplastic raw material-based fused deposition modeling 3D printing, aqueous slurry-based direct ink writing 3D printing, mechanically-assisted direct ink writing 3D printing, and photosensitive slurry-based vat photopolymerization 3D printing, are summarized; finally, the challenges in 3D printing of CFRCMCs are analyzed from fiber-ceramic interfaces, defect characterization and control, ceramization and densification, automation and intelligent manufacturing, structural and functional integration, 4D printing, self-healing, and standards. It is hoped that this review will provide some references and guidance for basic scientific and key technological research related to CFRCMCs 3D printing.

Key words： continuous fiber ceramic matrix fiber reinforcement composite material 3D printing

Received: 03 August 2024 Published: 05 February 2025

ZTFLH:

TB332

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	LI Zengchan
	WANG Wenqing
	WANG Gang
	HE Rujie

Cite this article:

LI Zengchan,WANG Wenqing,WANG Gang, et al. 3D printing of continuous fiber reinforced ceramic matrix composites: research development and challenges[J]. Materials Science and Engineering of Powder Metallurgy, 2024, 29(6): 423-448.

URL:

http://pmbjb.csu.edu.cn/EN/10.19976/j.cnki.43-1448/TF.2024068 OR http://pmbjb.csu.edu.cn/EN/Y2024/V29/I6/423

[1] ZHANG W Y, SHI F Y, WANG J W, et al.Preparation and properties of a porous ZrO₂/SiZrBoC ceramic matrix composite with high temperature resistance and low thermal conductivity[J]. Journal of the European Ceramic Society, 2024, 44(4): 2329-2337.
[2] ZHAO Y, ZHANG W J, WANG M H, et al.Low-density ZnTiO₃-ceramic hollow microsphere composite photocatalyst for degradation of azophloxine[J]. Journal of Alloys and Compounds, 2024, 995: 174846.
[3] ZHU T T, WU Z X, WANG Y D, et al.Sintering of silicomanganese slag-reinforced porous SiC ceramic membrane supports with high alkali corrosion resistance[J]. Ceramics International, 2024, 50(2): 3921-3929.
[4] DU J G, ZHANG H Z, GENG Y M, et al.A review on machining of carbon fiber reinforced ceramic matrix composites[J]. Ceramics International, 2019, 45(15): 18155-18166.
[5] DHANASEKAR S, GANESAN A T, RANI T L, et al.A comprehensive study of ceramic matrix composites for space applications[J]. Advances in Materials Science and Engineering, 2022, 2022: 6160591.
[6] GERINGER J W, KATOH Y, GONCZY S, et al.Codes and standards for ceramic composite core materials for high temperature reactor applications[J]. Nuclear Engineering and Design, 2023, 405: 112158.
[7] JIA C, XU Z, LUO D, et al.Flexible ceramic fibers: recent development in preparation and application[J]. Advanced Fiber Materials, 2022, 4(4): 573-603.
[8] MOR M, MEISER M, LANGHOF N, et al.Tribological behavior of carbon fiber reinforced ZrB₂ based ultra high temperature ceramics[J]. Journal of the European Ceramic Society, 2023, 43(13): 5413-5424.
[9] MA Y Y, WANG J T, ZHAO G Z, et al.New insights into the damage assessment and energy dissipation weight mechanisms of ceramic/fiber laminated composites under ballistic impact[J]. Ceramics International, 2023, 49(13): 21966-21977.
[10] ZHANG Q Z, ZHOU W, PANG L, et al.Design and numerical studies of microwave absorption structure based on hybrid weave of fibers with different dielectric properties[J]. Composite Structures, 2023, 323: 117460.
[11] HU P L, SHAN Z D, ZANG Y, et al.High temperature thermal conductivity of fiber hybrid ceramic matrix composites with different modes[J]. Advanced Engineering Materials, 2024, 10(26): 2301552.
[12] LI L B, LIU Y F, WANG Y L.Estimate constituent properties of 3D needle-punched C/SiC composites from hysteresis loops[J]. International Journal of Fatigue, 2023, 170: 107543.
[13] PENG Y Q, LI Z W, LI A J, et al.Mechanical and tribological properties of C/C-SiC ceramic composites with different preforms[J]. Science and Engineering of Composite Materials, 2023, 30(1): 20220205.
[14] MEI H, YAN Y K, FENG L P, et al.First printing of continuous fibers into ceramics[J]. Journal of the American Ceramic Society, 2018, 102(6): 3244-3255.
[15] ZHAO Z, ZHOU G X, YANG Z H, et al.Direct ink writing of continuous SiO₂ fiber reinforced wave-transparent ceramics[J]. Journal of Advanced Ceramics, 2020, 9(4): 403-412.
[16] CRAMER C L, YOON B, LANCE M J, et al.Additive manufacturing of C/C-SiC ceramic matrix composites by automated fiber placement of continuous fiber tow in polymer with pyrolysis and reactive silicon melt infiltration[J]. Journal of Composites Science, 2022, 6(12): 359.
[17] SUN J X, YU S X, WADE-ZHU J, et al.3D printing of layered ceramic/carbon fiber composite with improved toughness[J]. Additive Manufacturing, 2022, 50: 102543.
[18] ZHANG L, WANG W Q, GAO X, et al.Additive manufacturing of continuous carbon fiber reinforced high entropy ceramic matrix composites via paper laminating, direct slurry writing, and precursor infiltration and pyrolysis[J]. Ceramics International, 2023, 49(5): 7833-7841.
[19] LI S, ZHANG H T, LU Z L, et al.Fabrication of bamboo-inspired continuous carbon fiber-reinforced SiC composites via dual-material thermally assisted extrusion-based 3D printing[J]. Journal of Materials Science & Technology, 2024, 208: 92-103.
[20] GULCAN O, GUNAYDIN K, TAMER A.The state of the art of material jetting: a critical review[J]. Polymers, 2021, 13(16): 2829.
[21] LV X F, YE F, CHENG L F, et al.Binder jetting of ceramics: powders, binders, printing parameters, equipment, and post-treatment[J]. Ceramics International, 2019, 45(10): 12609-12624.
[22] DU W C, REN X R, PEI Z J, et al.Ceramic binder jetting additive manufacturing: a literature review on density[J]. Journal of Manufacturing Science and Engineering, 2020, 142(4): 040801.
[23] KUNCHALA P, KAPPAGANTULA K.3D printing high density ceramics using binder jetting with nanoparticle densifiers[J]. Materials & Design, 2018, 155: 443-450.
[24] FLORIO K, PUCCIO D, VIGANÒ G, et al.Process characterization and analysis of ceramic powder bed fusion[J]. The International Journal of Advanced Manufacturing Technology, 2021, 117(7/8): 2105-2116.
[25] REHMAN A U, NAVARRETE-SEGADO P, SALAMCI M U, et al.Understanding the consolidation mechanism of selective laser sintering/powder bed selective laser process of ceramics: hydroxyapatite case[J]. Rapid Prototyping Journal, 2024, 30(4): 677-695.
[26] LI S C, LIU D F, MI H B, et al.Numerical simulation on evolution process of molten pool and solidification characteristics of melt track in selective laser melting of ceramic powder[J]. Ceramics International, 2022, 48(13): 18302-18315.
[27] MOSTAFAEI A, ZHAO C, HE Y N, et al.Defects and anomalies in powder bed fusion metal additive manufacturing[J]. Current Opinion in Solid State and Materials Science, 2022, 26(2): 100974.
[28] MAURYA H S, KOSIBA K, JUHANI K, et al.Effect of powder bed preheating on the crack formation and microstructure in ceramic matrix composites fabricated by laser powder-bed fusion process[J]. Additive Manufacturing, 2022, 58: 103013.
[29] WANG Y R, SU R Y, CHEN J Y, et al.3D printed bioinspired flexible absorber: toward high-performance electromagnetic absorption at 75-110 GHz[J]. ACS Applied Materials & Interfaces, 2023, 15(46): 53996-54005.
[30] CHEN J Y, SU R Y, ZHAI X F, et al.Improving the accuracy of stereolithography 3D printed Al₂O₃ microcomponents by adding photoabsorber: fundamentals and experiments[J]. Journal of Materials Research and Technology, 2023, 27: 757-766.
[31] SU R Y, CHEN J Y, ZHANG X F, et al.Accuracy controlling and mechanical behaviors of precursor-derived ceramic SiOC microlattices by projection micro stereolithography (PμSL) 3D printing[J]. Journal of Advanced Ceramics, 2023, 12(11): 2134-2147.
[32] WU X Q, TENG J C, JI X X, et al.Research progress of the defects and innovations of ceramic vat photopolymerization[J]. Additive Manufacturing, 2023, 65: 103441.
[33] ZHOU Q, SU X N, WU J Q, et al.Additive manufacturing of bioceramic implants for restoration bone engineering: technologies, advances, and future perspectives[J]. ACS Biomaterials Science & Engineering, 2023, 9(3): 1164-1189.
[34] ZHANG X Q, ZHANG K Q, ZHANG L, et al.Additive manufacturing of cellular ceramic structures: from structure to structure-function integration[J]. Materials & Design, 2022, 215: 110470.
[35] ASAD H, IHSANULLAH K.A review of laminated object manufacturing (LOM) aspects and various processes used in it[J]. International Journal of Advanced Engineering Research and Science, 2023, 10(1): 46-54.
[36] ISHFAQ K, ABAS Z, KUMAR M S, et al.Review of recent trends in ultrasonic additive manufacturing: current challenges and future prospects[J]. Rapid Prototyping Journal, 2023, 29(6): 1195-1211.
[37] CHENG L F, SUN M Y, YE F, et al.Structure design, fabrication, properties of laminated ceramics: a review[J]. International Journal of Lightweight Materials and Manufacture, 2018, 1(3): 126-141.
[38] ZHENG Q Y, XIE B, XU Z L, et al.A systematic printability study of direct ink writing towards high-resolution rapid manufacturing[J]. International Journal of Extreme Manufacturing, 2023, 5(3): 035002.
[39] GONZALEZ-GUTIERREZ J, CANO S, SCHUSCHNIGG S, et al.Additive manufacturing of metallic and ceramic components by the material extrusion of highly-filled polymers: a review and future perspectives[J]. Materials, 2018, 11(5): 840.
[40] ROMANCZUK-RUSZUK E, SZTORCH B, PAKUŁA D, et al. 3D printing ceramics: materials for direct extrusion process[J]. Ceramics, 2023, 6(1): 364-385.
[41] PUZATOVA A, SHAKOR P, LAGHI V, et al.Large-scale 3D printing for construction application by means of robotic arm and gantry 3D printer: a review[J]. Buildings, 2022, 12(11): 2023.
[42] YAN Y K, MEI H, ZHANG M G, et al.Key role of interphase in continuous fiber 3D printed ceramic matrix composites[J]. Composites Part A: Applied Science and Manufacturing, 2022, 162: 107127.
[43] CHENG Y H, ZHANG Y X, ZHANG F, et al.Using flexible hydrothermal carbon-coated continuous carbon fiber to fabricate C_f/ZrB₂-SiC composites by fused deposition modeling and precursor infiltration pyrolysis[J]. Journal of the European Ceramic Society, 2024, 44(2): 721-728.
[44] CHEN R, BRATTEN A, RITTENHOUSE J, et al.Additive manufacturing of continuous carbon fiber-reinforced SiC ceramic composite with multiple fiber bundles by an extrusion-based technique[J]. Ceramics International, 2023, 49(6): 9839-9847.
[45] WANG W Q, GAO X, LI Z C, et al.Fiber-laying-assisted material extrusion additive manufacturing of continuous carbon fiber reinforced SiC ceramic matrix composites[J]. Materials Science and Engineering A, 2024, 890: 145944.
[46] AKHOUNDI B, BEHRAVESH A H, SAED A B.An innovative design approach in three-dimensional printing of continuous fiber-reinforced thermoplastic composites via fused deposition modeling process: in-melt simultaneous impregnation[J]. Proceedings of the Institution of Mechanical Engineers Part B-Journal of Engineering Manufacture, 2019, 234(1/2): 243-259.
[47] MORITZER E, ELSNER C L, SCHUMACHER C.Investigation of metal‐polymer composites manufactured by fused deposition modeling with regard to process parameters[J]. Polymer Composites, 2021, 42(11): 6065-6079.
[48] RAJAN K, SAMYKANO M, KADIRGAMA K, et al.Fused deposition modeling: process, materials, parameters, properties, and applications[J]. The International Journal of Advanced Manufacturing Technology, 2022, 120(3/4): 1531-1570.
[49] DEY A, YODO N.A systematic survey of FDM process parameter optimization and their influence on part characteristics[J]. Journal of Manufacturing and Materials Processing, 2019, 3(3): 64.
[50] MARTINI M, SCACCIA M, MARCHELLO G, et al.An outline of fused deposition modeling: system models and control strategies[J]. Applied Sciences, 2022, 12(11): 5400.
[51] LI S, ZHANG H T, HAN Y, et al.Thermally assisted extrusion-based 3D printing of continuous carbon fiber-reinforced SiC composites[J]. Composites Part A: Applied Science and Manufacturing, 2023, 172: 107593.
[52] LIU J, FENG K L, SU Z, et al. Dimensional deviations and distortion mechanism of polymer spur gear fabricated by fused deposition modeling[J]. Journal of Materials Engineering and Performance, [2024-08-03]. https://link.springer.com/article/10.1007/s11665-024-09321-w.
[53] WANG T, LI N Y, LINK G D, et al.Load-dependent path planning method for 3D printing of continuous fiber reinforced plastics[J]. Composites Part A: Applied Science and Manufacturing, 2021, 140: 106181.
[54] HUANG Y M, FANG G X, ZHANG T Y, et al.Turning-angle optimized printing path of continuous carbon fiber for cellular structures[J]. Additive Manufacturing, 2023, 68: 103501.
[55] DING W, LI H Y, LIU H L, et al.Thermal insulation and antioxidation of vertical graphene oxide‐grafted carbon nanofiber aerogels with ceramic coating[J]. Journal of the American Ceramic Society, 2022, 106(4): 2501-2514.
[56] KUMAR N M S, DHRUTHI N U D, SADASHIVA M, et al. Coatings on reinforcements in aluminum metal matrix composites[J]. International Journal of Metalcasting, 2022, 17(2): 1049-1064.
[57] LIU Y X, CHENG Y H, MA D H, et al.Continuous carbon fiber reinforced ZrB₂-SiC composites fabricated by direct ink writing combined with low-temperature hot-pressing[J]. Journal of the European Ceramic Society, 2022, 42(9): 3699-3707.
[58] FANG C, HU P, DONG S, et al.Influence of hydrothermal carbon coating on the properties of CF/ZrB₂/SiBCN prepared by slurry injection[J]. Journal of the European Ceramic Society, 2021, 41(1): 84-91.
[59] RODRÍGUEZ-ROJAS F, ZAMORA V, GUIBERTEAU F, et al. Effect of the degree of densification on the unlubricated sliding-wear behaviour of monolithic B₄C ceramics[J]. Tribology International, 2023, 186: 108656.
[60] GE M M, XIE D Q, YANG Y W, et al.Sintering densification mechanism and mechanical properties of the 3D-printed high-melting-point-difference magnesium oxide/calcium phosphate composite bio-ceramic scaffold[J]. Journal of the Mechanical Behavior of Biomedical Materials, 2023, 144: 105978.
[61] TANG S Y, YANG Y R, FAN Z T, et al.A novel composite binder design for direct ink writing alumina-based ceramics with enhanced strength at low sintering temperature[J]. Ceramics International, 2022, 48(6): 7963-7974.
[62] M’BARKI A, BOCQUET L, STEVENSON A. Linking rheology and printability for dense and strong ceramics by direct ink writing[J]. Scientific Reports, 2017, 7(1): 6017.
[63] CHAN S S L, SESSO M L, FRANKS G V. Direct ink writing of hierarchical porous alumina‐stabilized emulsions: rheology and printability[J]. Journal of the American Ceramic Society, 2020, 103(10): 5554-5566.
[64] CHEN R Y, BRATTEN A, RITTENHOUSE J, et al.Additive manufacturing of high mechanical strength continuous C_f/SiC composites using a 3D extrusion technique and polycarbosilane‐coated carbon fibers[J]. Journal of the American Ceramic Society, 2023, 106(7): 4028-4037.
[65] ZHU Z J, LIU R T, YAN J, et al.Effects of a polycarboxylate superplasticiser on the rheological properties of a portland-sulphoaluminate cement composite slurry[J]. Materials Letters, 2022, 317: 132147.
[66] SHEN M H, FU R L, LIU H B, et al.Photosensitive Si₃N₄ slurry with combined benefits of low viscosity and large cured depth for digital light processing 3D printing[J]. Journal of the European Ceramic Society, 2023, 43(3): 881-888.
[67] VATANDAS B B, USUN A, GUMRUK R, et al.The relationship between fiber bundle size and mechanical performance of additively manufactured continuous carbon fiber reinforced thermoplastic composites[J]. 3D Pringting and Additive Manufacturing, 2023, 10(6): 1190-1203.
[68] LIU K, QIU L, ZHANG Y Z, et al.Additive manufacturing of continuous carbon fiber-reinforced silicon carbide ceramic composites[J]. International Journal of Applied Ceramic Technology, 2023, 20(6): 3455-3469.
[69] HUANG L F, CHEN R Y, LI S S, et al.Microstructure and mechanical properties of continuous carbon fiber-reinforced SiC ceramic composite fabricated by direct ink writing[J]. Ceramics International, 2024, 50: 25679-25688.
[70] ZHENG W, WU J M, CHEN S, et al.Improved mechanical properties of SiC fiber reinforced silica-based ceramic cores fabricated by stereolithography[J]. Journal of Materials Science & Technology, 2022, 116: 161-168.
[71] TOFANGCHI A, HAN P, IZQUIERDO J, et al.Effect of ultrasonic vibration on interlayer adhesion in fused filament fabrication 3D printed ABS[J]. Polymers, 2019, 11(2): 315.
[72] KUNCIUS T, RIMASAUSKAS M, RIMASAUSKIENE R.Interlayer adhesion analysis of 3D-printed continuous carbon fibre-reinforced composites[J]. Polymers, 2021, 13(10): 1653.
[73] LI Z C, WANG W Q, GAO X, et al.Continuous carbon fiber reinforced SiC ceramic matrix composites by vertical fiber laying combined with material extrusion 3D printing[J]. Advanced Engineering Materials, 2024, 26(12): 2400218.
[74] WANG W Q, GAO X, LI Z C, et al.Effects of ceramic layer height on the mechanical properties of C_f/SiC ceramic matrix composites fabricated by fiber-laying-assisted material extrusion 3D printing[J]. Composites Communications, 2024, 48: 101926.
[75] ZHANG X Q, MENG Q Y, ZHANG K Q, et al.3D-printed bioinspired Al₂O₃/polyurea dual-phase architecture with high robustness, energy absorption, and cyclic life[J]. Chemical Engineering Journal, 2023, 463: 142378.
[76] LI S W, WANG G, ZHANG K Q, et al.Mechanical properties of Al₂O₃ and Al₂O₃/Al interpenetrated functional gradient structures by 3D printing and melt infiltration[J]. Journal of Alloys and Compounds, 2023, 950: 169948.
[77] LU J J, ZHANG X Q, LI S W, et al.Quasi-static compressive and cyclic dynamic impact performances of vat photopolymerization 3D printed Al₂O₃ triply periodic minimal surface scaffolds and Al₂O₃/Al hybrid structures: effects of cell size[J]. Journal of Alloys and Compounds, 2023, 969: 172445.
[78] XU Z K, SUN X H, XIONG K Z, et al.A review of the research progress on the interface between oxide fiber and oxide ceramic matrix[J]. Ceramics International, 2021, 47(5): 5896-5908.
[79] LUO X Y, ZHENG H, LAI W D, et al.Defect engineering of carbons for energy conversion and storage applications[J]. Energy & Environmental Materials, 2023, 6(3): e12402.
[80] CHEN P C, MIAO W C, AHMED T, et al.Defect inspection techniques in SiC[J]. Nanoscale Research Letters, 2022, 17(1): 30.
[81] AI S G, SONG W L, CHEN Y F.Stress field and damage evolution in C/SiC woven composites: image-based finite element analysis and in situ X-ray computed tomography tests[J]. Journal of the European Ceramic Society, 2021, 41(4): 2323-2334.
[82] SAÂDAOUI M, KHALDOUN F, ADRIEN J, et al. X-ray tomography of additive-manufactured zirconia: processing defects-strength relations[J]. Journal of the European Ceramic Society, 2020, 40(8): 3200-3207.
[83] 翟小菲, 陈婧祎, 张学勤, 等. 陶瓷型芯3D打印研究进展与挑战[J]. 陶瓷学报, 2023, 44(5): 831-848.
ZHAI Xiaofei, CHEN Jingyi, ZHANG Xueqin, et al.Recent progresses and challenges of 3D printing of ceramic cores[J]. Journal of Ceramics, 2023, 44(5): 831-848.
[84] ZHANG K Q, MENG Q Y, QU Z L, et al.A review of defects in vat photopolymerization additive-manufactured ceramics: characterization, control, and challenges[J]. Journal of the European Ceramic Society, 2024, 44(3): 1361-1384.
[85] ZHANG K Q, MENG Q Y, CAI N J, et al.Effects of solid loading on stereolithographic additive manufactured ZrO₂ ceramic: a quantitative defect study by X-ray computed tomography[J]. Ceramics International, 2021, 47(17): 24353-24359.
[86] HOSSAIN S S, LU K.Recent progress of alumina ceramics by direct ink writing: ink design, printing and post-processing[J]. Ceramics International, 2023, 49(7): 10199-10212.
[87] CHAVEZ L A, IBAVE P, WILBURN B, et al.The influence of printing parameters, post-processing, and testing conditions on the properties of binder jetting additive manufactured functional ceramics[J]. Ceramics, 2020, 3(1): 65-77.
[88] BAI X J, DING G J, ZHANG K Q, et al.Stereolithography additive manufacturing and sintering approaches of SiC ceramics[J]. Open Ceramics, 2021, 5: 100046.
[89] SUN G D, ZHANG C, ZHANG Q, et al.Microstructure and mechanical properties of SiC_f/SiC composite prepared by chemical vapor infiltration[J]. Ceramics International, 2022, 48(24): 36983-36991.
[90] LYU Y, DU B H, CHEN G Q, et al.Microstructural regulation, oxidation resistance, and mechanical properties of C_f/SiC/SiHfBOC composites prepared by chemical vapor infiltration with precursor infiltration pyrolysis[J]. Journal of Advanced Ceramics, 2021, 11(1): 120-135.
[91] TANG J, LIU M, WEI Y Q, et al.An efficient and low-cost liquid silicon infiltration method to prepare SiC-coated carbon short fiber for fiber protection of C_f/SiC ceramic matrix composites[J]. Ceramics International, 2021, 47(9): 13235-13241.
[92] YANG Z S, JIN L, YAN Y L, et al.Filament breakage monitoring in fused deposition modeling using acoustic emission technique[J]. Sensors, 2018, 18(3): 749.
[93] TAMIR T S, XIONG G, FANG Q H, et al.Machine-learning-based monitoring and optimization of processing parameters in 3D printing[J]. International Journal of Computer Integrated Manufacturing, 2022, 36(9): 1362-1378.
[94] HUNDE B R, WOLDEYOHANNES A D.Future prospects of computer-aided design (CAD): a review from the perspective of artificial intelligence (AI), extended reality, and 3D printing[J]. Results in Engineering, 2022, 14: 100478.
[95] LU L, HOU J, YUAN S Q, et al.Deep learning-assisted real-time defect detection and closed-loop adjustment for additive manufacturing of continuous fiber-reinforced polymer composites[J]. Robotics and Computer-Integrated Manufacturing, 2023, 79: 102431.
[96] CHOU Y L, MOREIRA C, BRUZA P, et al.Counterfactuals and causability in explainable artificial intelligence: theory, algorithms, and applications[J]. Information Fusion, 2022, 81: 59-83.
[97] YAMAMOTO K, LUCES J V S, SHIRASU K, et al. A novel single-stroke path planning algorithm for 3D printers using continuous carbon fiber reinforced thermoplastics[J]. Additive Manufacturing, 2022, 55: 102816.
[98] TAO F, XIAO B, QI Q L, et al.Digital twin modeling[J]. Journal of Manufacturing Systems, 2022, 64: 372-389.
[99] LIU X F, HE J F, LI Y G, et al.Foam-gelcasting preparation of porous SiC ceramic for high-temperature thermal insulation and infrared stealth[J]. Rare Metals, 2023, 42(11): 3829-3838.
[100] SU R Y, CHEN J Y, ZHANG X Q, et al.3D-printed micro/nano-scaled mechanical metamaterials: fundamentals, technologies, progress, applications, and challenges[J]. Small, 2023, 19(29): e2206391.
[101] WANG W Q, LI Z C, GAO X, et al.Material extrusion 3D printing of large-scale SiC honeycomb metastructure for ultra-broadband and high temperature electromagnetic wave absorption[J]. Additive Manufacturing, 2024, 85: 104158.
[102] SUN M Y, YU Y F, AN K, et al.Active frequency selective rasorber based on fiber-reinforced SiO₂ ceramic matrix composite[J]. IEEE Transactions on Electromagnetic Compatibility, 2022, 64(5): 1593-1601.
[103] WANG C S, WU S Q, LI Z Q, et al.3D printed porous biomass-derived SiC_nw/SiC composite for structure-function integrated electromagnetic absorption[J]. Virtual and Physical Prototyping, 2022, 17(3): 718-733.
[104] FENG P, ZHAO R Y, TANG W M, et al.Structural and functional adaptive artificial bone: materials, fabrications, and properties[J]. Advanced Functional Materials, 2023, 33(23): 2214726.
[105] KHALID M Y, ARIF Z U, NOROOZI R, et al.4D printing of shape memory polymer composites: a review on fabrication techniques, applications, and future perspectives[J]. Journal of Manufacturing Processes, 2022, 81: 759-797.
[106] HE R J, ZHOU N P, ZHANG K Q, et al.Progress and challenges towards additive manufacturing of SiC ceramic[J]. Journal of Advanced Ceramics, 2021, 10(4): 637-674.
[107] LIU G, LU X Y, ZHANG X F, et al.3D/4D additive-subtractive manufacturing of heterogeneous ceramics[J]. Journal of Materials Science & Technology, 2024, 201: 210-221.
[108] LIU G, ZHANG X F, LU X Y, et al.4D additive-subtractive manufacturing of shape memory ceramics[J]. Advanced Materials, 2023, 35(39): 2302108.
[109] WANG R, YUAN C, CHENG J X, et al.Direct 4D printing of ceramics driven by hydrogel dehydration[J]. Natrue Communications, 2024, 15(1): 758.
[110] PALADUGU S R M, SREEKANTH P S R, SAHU S K, et al. A comprehensive review of self-healing polymer, metal, and ceramic matrix composites and their modeling aspects for aerospace applications[J]. Materials, 2022, 15(23): 8521.
[111] HUANG J G, GUO L J, ZHONG L.Synergistic healing mechanism of self-healing ceramics coating[J]. Ceramics International, 2022, 48(5): 6520-6527.
[112] SEKINE N, NAKAO W.Advanced self-healing ceramics with controlled degradation and repair by chemical reaction[J]. Materials, 2023, 16(19): 6368.
[113] BABAFEMI A J, KOLAWOLE J T, MIAH M J, et al.A concise review on interlayer bond strength in 3D concrete printing[J]. Sustainability, 2021, 13(13): 7137.
[114] CHENG F, HU Y S, YUAN B Y, et al.Transverse and longitudinal flexural properties of unidirectional carbon fiber composites interleaved with hierarchical aramid pulp micro/nano-fibers[J]. Composites Part B: Engineering, 2020, 188: 107897.
[115] ZHANG P F, QIU Y, YE C, et al.Anisotropically conductive phase change composites enabled by aligned continuous carbon fibers for full-spectrum solar thermal energy harvesting[J]. Chemical Engineering Journal, 2023, 461: 141940.
[116] GOH G D, DIKSHIT V, AN J, et al.Process-structure-property of additively manufactured continuous carbon fiber reinforced thermoplastic: an investigation of mode I interlaminar fracture toughness[J]. Mechanics of Advanced Materials and Structures, 2020, 29(10): 1418-1430.