氧燃比对爆炸喷涂铁基非晶涂层结构和摩擦磨损性能的影响

Abstract
Figure/Table
References
Related Citation (1)

Download: PDF (597 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract The Fe-based amorphous coatings were prepared by detonation spray at various oxygen fuel rates (oxygen flow m³/h to acetylene flow m³/h ratio). The effects of oxygen fuel rate on coating microstructure and wear properties were examined. The effects of microhardness and porosity on the wear properties are also studied. The results show, the amorphous phase contents of coatings were calculated to be 89.73%, 86.23% and 81.46%, respectively, which were higher than those fabricated by other thermal spray techniques. The porosity was tested to be 2.1%, 1.4% and 0.8%, respectively. The wear resistance of Fe-based amorphous coatings was four times better than the stainless steel substrate. The oxygen fuel rate of 1.2:1.0 was proved to be the optimal parameter of fabricating Fe-based amorphous coating. Amorphous coatings with moderate hardness and porosity have the best wear resistance, and the effect of hardness on wear resistance is greater than that of porosity.

Key words： detonation spray iron-based amorphous coating oxygen fuel rate wear properties

Received: 02 December 2018 Published: 11 July 2019

ZTFLH:

TG139⁺.8

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	XIE Lu
	XIONG Xiang
	WANG Yueming

Cite this article:

XIE Lu,XIONG Xiang,WANG Yueming. Effects of oxygen fuel rate on microstructure and wear properties of detonation sprayed iron-based amorphous coatings[J]. Materials Science and Engineering of Powder Metallurgy, 2019, 24(3): 261-266.

URL:

http://pmbjb.csu.edu.cn/EN/ OR http://pmbjb.csu.edu.cn/EN/Y2019/V24/I3/261

[1] ZHOU Y Y, MA G Z, WANG H D, et al.Fabrication and characterization of supersonic plasma sprayed Fe-based amorphous metallic coatings[J]. Materials & Design, 2016, 110(5): 332-339.
[2] ZHANG X, WANG Z, LIN J, et al.A study on high temperature oxidation behavior of high-velocity arc sprayed Fe-based coatings[J]. Surface and Coatings Technology, 2015, 283(15): 255-261.
[3] ZHANG J, LIU M, SONG J, et al.Microstructure and corrosion behavior of Fe-based amorphous coating prepared by HVOF[J]. J Alloy Compd, 2017, 721(15): 506-511.
[4] ZHANG S D, ZHANG W L, WANG S G, et al.Characterisation of three-dimensional porosity in an Fe-based amorphous coating and its correlation with corrosion behaviour[J]. Corros Sci, 2015, 93(4): 211-221.
[5] ZHANG C, CHU Z, WEI F, et al.Optimizing process and the properties of the sprayed Fe-based metallic glassy coating by plasma spraying[J]. Surface and Coatings Technology, 2017, 319(15): 1-5.
[6] ZHANG H, XIE Y, HUANG L, et al.Effect of feedstock particle sizes on wear resistance of plasma sprayed Fe-based amorphous coatings[J]. Surface and Coatings Technology, 2014, 258(15): 495-502.
[7] GUO W, ZHANG J, WU Y, et al.Fabrication and characterization of Fe-based amorphous coatings prepared by high-velocity arc spraying[J]. Materials & Design, 2015, 78(5): 118-124.
[8] HSIEH H H, KAI W, HUANG R T, et al.Air oxidation of an Fe₄₈Cr₁₅C₁₅Mo₁₄B₆Er₂ bulk metallic glass at 600-725 ℃[J]. Materials Transactions, 2007, 48(7): 1864-1869.
[9] WU H, LAN X D, LIU Y, et al.Fabrication, tribological and corrosion behaviors of detonation gun sprayed Fe-based metallic glass coating[J]. T Nonferr Metal Soc, 2016, 26(6): 1629-1637.
[10] WANG Y, ZHENG Y G, KE W, et al.Slurry erosion-corrosion behaviour of high-velocity oxy-fuel (HVOF) sprayed Fe-based amorphous metallic coatings for marine pump in sand-containing NaCl solutions[J]. Corros Sci, 2011, 53(10): 3177-3185.
[11] WANG Y, XING Z Z, LUO Q, et al.Corrosion and erosion- corrosion behaviour of activated combustion high-velocity air fuel sprayed Fe-based amorphous coatings in chloride-containing solutions[J]. Corros Sci, 2015, 98(9): 339-353.
[12] WANG Y, LI G, SHI Z, et al.Effects of graphite addition on the microstructure and properties of laser cladding Zr-Al-Ni-Cu amorphous coatings[J]. J Alloy Compd, 2014, 610(15): 713-717.
[13] WANG T G, LIU Y, WANG Q, et al.Influence of residual stress on the adhesive behavior of detonation gun sprayed WC-Co coatings[J]. Current Applied Physics, 2012, 12(2): S59-S62.
[14] KOMAKI M, MIMURA T, KUSUMOTO Y, et al.Formation of Fe-based amorphous coating films by thermal spraying technique[J]. Materials Transactions, 2010, 51(9): 1581-1585.
[15] CHU Z, YANG Y, CHEN X, et al.Characterization and tribology performance of Fe-based metallic glassy composite coatings fabricated by gas multiple-tunnel plasma spraying[J]. Surface and Coatings Technology, 2016, 292(25): 44-48.
[16] PIAO Z Y, XU B S, WANG H D, et al.Characterization of Fe-based alloy coating deposited by supersonic plasma spraying[J]. Fusion Engineering and Design, 2013, 88(11): 2933-2938.
[17] ZHOU Z, WANG L, WANG F C, et al.Formation and corrosion behavior of Fe-based amorphous metallic coatings prepared by detonation gun spraying[J]. T Nonferr Metal Soc, 2009, 19(3): 634-638.
[18] ZHOU Z, WANG L, HE D Y, et al.Microstructure and electrochemical behavior of Fe-based amorphous metallic coatings fabricated by atmospheric plasma spraying[J]. J Therm Spray Techn, 2010, 20(1/2): 344-350.
[19] ULIANITSKY V Y, DUDINA D V, BATRAEV I S, et al.Detonation spraying of titanium and formation of coatings with spraying atmosphere-dependent phase composition[J]. Surface and Coatings Technology, 2015, 261(15): 174-180.
[20] BABU P S, RAO D S, KRISHNA L R, et al.Weibull analysis of hardness distribution in detonation sprayed nano-structured WC-12Co coatings[J]. Surf Coat Tech, 2017, 319(15): 394-402.
[21] BAINS P S, GREWAL J S, SIDHU S S, et al.Wear between ring and traveler: A pin-on-disc mapping of various detonation gun sprayed coatings[C]// Materials Today: Proceedings, 2017, 4(2): 369-378.